Cisco Systems PRP-1=, PRP-1/R=, PRP-2=, PRP-2/R= manual Soft Reset Switch, Flash Disk Slots

Page 16

Product Overview

Soft Reset Switch

A soft reset switch provides a reset to the processor software on the PRP. You access the soft reset switch through a small opening in the PRP faceplate. To depress the switch, insert a paper clip or a similar object into the opening.

Caution The soft reset switch is not a mechanism for resetting the PRP and reloading the IOS image. It is intended for software development use. To prevent system problems or loss of data, use the soft reset switch only on the advice of Cisco service personnel.

Flash Disk Slots

The PRP includes two Flash disk slots on the front panel of the card. Either slot on the PRP-1 can support an ATA Flash disk or a linear Flash memory card. The Flash disk slots on the PRP-2 can only support ATA Flash disks.

Note The PRP only supports +5 VDC Flash disk devices. It does not support +3.3 VDC Flash disk devices.

All combinations of different Flash devices are supported by the PRP-1. You can use ATA Flash disks, linear Flash memory cards, or a combination of the two.

Each Flash disk slot has an ejector button for ejecting a card from the slot. See the “Using Flash Disks in the PRP” section on page 61 for more information.

Note Linear Flash memory cards may not have the capacity to meet the requirements of your configuration. However, they can be used for emergency file recovery applications.

	Performance Route Processor Installation and Configuration Guide
16	OL-11656-01

Image 16

Contents Document Contents Router Information Important InformationSupported Platforms Cisco IOS Software Requirements PRP RedundancyHardware Revision Requirements Output from a later software release would be as followsProduct Overview Related DocumentationPRP Functions Shows the front panel view of the PRP-2PRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Type Size Quantity Description Location Program boot imageMB fixed Secondary CPU cache memory functions Sdram Flash Memory PRP LEDsStatus LEDs Following LEDs are used on the PRPCisco IOS System Error Messages publications Display LEDsSoft Reset Switch Flash Disk SlotsEthernet Ports Asynchronous Serial PortsHard Disk Drive Safety Guidelines Preparing for InstallationCompact Flash Disk Preventing Electrostatic Discharge Required Tools and Equipment Removing and Installing a PRPWorking with Electrical Equipment Removing a PRP Illustrates the PRP installed in a chassis Ejector LeversShows the ejector levers in detail Installing a PRP Removing and Installing a PRP Checking the Installation PRP Boot ProcessStarting the System and Observing Initial Conditions Rommon for this PRP is enabled and recognized by the system Cisco IOS is enabled and this PRP is the active PRPCisco IOS is enabled and this PRP is in standby mode LED Display DescriptionChecking the Installation Checking the Installation Verifying Interface Status Upgrading to the PRP ETH BitsUpgrading to the PRP Without Rebooting the Router Router# show redundancyRouter# dir disk1 SSO or RPR+ mode because the RPs are running the same image Is correct, continue with StepAnother disk or at another location Prompted to abort the copy, type nUpgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP With Rebooting the Router Verify the disk contents using the dir disk1 commandUpgrading to the PRP Use the command upgrade rom-monitor slot rp-slot Differentiating Between PRP-1 and PRP-2 0x10Configuring an Ethernet Interface Configuring Interfaces on the PRPEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Ethernet Port Pin Signal Description Crossover Cable Pinout for Connecting Two PRPsParameter RJ-45 Lists Ieee 802.3u physical characteristics for 100BASE-TXParameter Ethernet Interface Cable Connection Procedure Configuring the Ethernet Interfaces Using the Ethernet Port on the PRPUsing Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Configuring the Auxiliary Interface Signal Input/Output DescriptionUnderstanding the Software Configuration Register Description of the Software Configuration RegisterAdditional Configuration and Maintenance Tasks Defines the bits in the software configuration register Bit Number Hexadecimal Value Meaning/FunctionBoot Field Meaning Boot Field SettingsDescribed in Table Configuring the Software Configuration Register Command PurposeBits in the Software Configuration Register Action/Filename BitData Transmission Rate bps Address net host9600 4800 1200 2400 Using Flash Disks in the PRP About Flash DisksRemoving and Installing a Flash Disk in the PRP Product NumberInstalling and Removing a Flash Disk Installing a Flash Disk Working with Flash DisksBooting from a Flash Disk Boots the named file from the Flash disk in slotRemoving and Installing a Compact Flash Disk Removing the CF from the PRP-2 BoardRemoving and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory GB Dimm U15 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18GB DIMMs U15 and U18 Removing a Dimm Cisco Product Number Dimm Modules Sdram Dimm SocketsDimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Regulatory, Compliance, and Safety Information Checking the Dimm InstallationElectromagnetic Compatibility Regulatory Statements Translated Safety Warnings and Agency ApprovalsFCC Class a Compliance Canada Europe EURegulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Cisco.com Obtaining DocumentationProduct Documentation DVD Cisco Product Security Overview Documentation FeedbackOrdering Documentation Reporting Security Problems in Cisco Products For emergencies only security-alert@cisco.comObtaining Technical Assistance Product Alerts and Field NoticesCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01