Cisco Systems PRP-1/R=, PRP-1=, PRP-2=, PRP-2/R= manual Canada, Europe EU

Page 81

Regulatory, Compliance, and Safety Information

•Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

CISPR 22

This apparatus complies with CISPR 22/EN55022 Class B radiated and conducted emissions requirements.

Canada

English Statement of Compliance

This class A digital apparatus complies with Canadian ICES-003.

French Statement of Compliance

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

Europe (EU)

This apparatus complies with EN55022 Class B and EN55024 standards when used as ITE/TTE equipment, and EN300386 for Telecommunications Network Equipment (TNE) in both installation environments, telecommunication centers and other indoor locations.

		Performance Route Processor Installation and Configuration Guide

	OL-11656-01			81
	OL-11656-01			81

Image 81

Contents Document Contents Important Information Router InformationSupported Platforms PRP Redundancy Cisco IOS Software RequirementsOutput from a later software release would be as follows Hardware Revision RequirementsRelated Documentation Product OverviewShows the front panel view of the PRP-2 PRP FunctionsPRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Program boot image Type Size Quantity Description LocationMB fixed Secondary CPU cache memory functions Sdram PRP LEDs Flash MemoryStatus LEDs Following LEDs are used on the PRPDisplay LEDs Cisco IOS System Error Messages publicationsFlash Disk Slots Soft Reset SwitchAsynchronous Serial Ports Ethernet PortsHard Disk Drive Preparing for Installation Safety GuidelinesCompact Flash Disk Preventing Electrostatic Discharge Removing and Installing a PRP Required Tools and EquipmentWorking with Electrical Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassisShows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the InstallationStarting the System and Observing Initial Conditions Cisco IOS is enabled and this PRP is the active PRP Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is in standby mode LED Display DescriptionChecking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRPRouter# show redundancy Upgrading to the PRP Without Rebooting the RouterRouter# dir disk1 Is correct, continue with Step SSO or RPR+ mode because the RPs are running the same imageAnother disk or at another location Prompted to abort the copy, type nUpgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the RouterUpgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2Configuring Interfaces on the PRP Configuring an Ethernet InterfaceEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal DescriptionLists Ieee 802.3u physical characteristics for 100BASE-TX Parameter RJ-45Parameter Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet InterfacesUsing Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary InterfaceDescription of the Software Configuration Register Understanding the Software Configuration RegisterAdditional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration registerBoot Field Settings Boot Field MeaningDescribed in Table Command Purpose Configuring the Software Configuration RegisterAction/Filename Bit Bits in the Software Configuration RegisterAddress net host Data Transmission Rate bps9600 4800 1200 2400 About Flash Disks Using Flash Disks in the PRPProduct Number Removing and Installing a Flash Disk in the PRPInstalling and Removing a Flash Disk Working with Flash Disks Installing a Flash DiskBoots the named file from the Flash disk in slot Booting from a Flash DiskRemoving the CF from the PRP-2 Board Removing and Installing a Compact Flash DiskRemoving and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18 GB Dimm U15GB DIMMs U15 and U18 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a DimmDimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety InformationTranslated Safety Warnings and Agency Approvals Electromagnetic Compatibility Regulatory StatementsFCC Class a Compliance Europe EU CanadaRegulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Obtaining Documentation Cisco.comProduct Documentation DVD Documentation Feedback Cisco Product Security OverviewOrdering Documentation For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco ProductsProduct Alerts and Field Notices Obtaining Technical AssistanceCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01