FEIN Power Tools WPO14-25E, WPO14-15E manual Handling hazardous dusts

Page 7

3 41 01 130 21 0.book Seite 7 Freitag, 18. Dezember 2009 7:47 07

en 7

This double-insulated power tool is equipped with a polarized plug (one contact is wider than the other). The plug will only fit into the polar- ized socket outlet in one position. Turn the plug if it does not fit completely into the socket out- let. If the plug still does not fit, have a qualified electrician install a polarized socket outlet. Do not modify or alter the plug under any circum- stances. Double-insulated power tools nei- ther require a three-core power cable nor a power connection with ground contact.

Operate the power tool only off power supplies whose voltage and frequency values corre- spond with the values on the type plate of the power tool.

If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Using special rubber protective gloves and footwear increases your own safety.

NOTE: Such a device is also known as ground fault circuit interrupter (GFCI) or earth leak- age circuit breaker (ELCB).

Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

Before mounting or replacing application tools or accessories, pull the power plug. This pre- ventive safety measure rules out the danger of injuries through accidental starting of the power tool.

Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explo- sion. Penetrating a water line causes property damage or may cause an electric shock.

Do not direct the power tool against yourself, other persons or animals. Danger of injury from sharp or hot application tools.

Do not rivet or screw any name-plates or signs onto the power tool. If the insulation is dam- aged, protection against an electric shock will be ineffective. Adhesive labels are recom- mended.

Always work using the auxiliary handle. The auxiliary handle ensures reliable guidance of the power tool.

Before putting into operation, check the main connection and the main plug for damage.

Handling hazardous dusts

WARNING When working with power tools, such as when grinding,

sanding, polishing, sawing or for other work procedures where material is removed, dusts develop that are both hazardous to one’s health and can spontaneously combust or be explo- sive.

Contact with or inhaling some dust types can trigger allergic reactions to the operator or bystanders and/or lead to respiratory infec- tions, cancer, birth defects or other repro- ductive harm.

Examples of such materials and therein con- tained chemicals, where hazardous dusts can develop when working them, are:

Asbestos and materials containing asbestos;

Lead-containing coatings, some wood types such as beech and oak;

Minerals and metal;

Silicate particles from bricks, concrete and other materials containing stone;

Solvent from solvent-containing paint/var- nish;

Arsenic, chromium and other wood pre- servatives;

Materials for pesticide treatment on boot and ship hulls.

To minimise the unwanted intake of these materials:

Use dust extraction matched appropriately for the developing dust.

Use personal protective equipment, such as a P2 filter-class dust protection mask.

Provide for good ventilation of the work- place.

Image 7
Contents USA Français Mode demploi Español Instrucciones de uso 3Personal safety For your safetyGeneral Safety Rules 1Work area safety4Power tool use and care Special safety instructionsKickback and related warnings Further safety warnings Safety warnings specific for sanding operationsSafety Warnings specific for Polishing operations Safety warnings specific for wire brushing operationsProvide for good ventilation of the work- place Handling hazardous dustsHand/arm vibrations 100 150 Extension cord10 en Intended use of the power toolSymbols Operation of the power tool off power generatorsOr fatal injury Symbol ExplanationDB, min, m/s2 Tional system of units SI 12 en Technical description and specificationsMounting the gear housing cover Figure Assembly instructionsMounting the auxiliary handle Figure Mounting the polishing tool Figure Switching on and OFF FigureChanging the tool Working instructionsSecuring the work piece Setting the speed FigureCleaning MaintenanceWarranty and liability ServiceAuxiliary handle Allen key Provided Accessories Figure18 en Selection of accessories Figures41 01 130 21 0.book Seite 19 Freitag, 18. Dezember 2009 747 20 en WPO14-15E 22 en 1Place de travail Pour votre sécurité2Sécurité relative au système électrique 4Utilisation et emploi soigneux de l’outil élec- troportatif 24 frInstructions particulières de sécurité Service26 fr Rebonds et mises en garde correspondantesConsignes de sécurité supplémentaires Veillez à bien aérer la zone de travail Maniement de poussières nocives28 fr ’amiante et les matériaux contenant de l’amianteLégers peuvent causer une auto-inflammation ou une explosion Vibrations mains-bras30 fr Câble de rallonge11,5 Reuse SymbolesConception de l’outil électrique Phique ci-contreHz, N, C, dB Min, m/s2 Symbol ExplicationQui peut entraîner de graves blessures ou la mort Produit avec double isolation ou isolation renforcéeDescription technique et spécification 34 fr Indications de montageMontage de la poignée supplémentaire Figure Montage du capot de la poignée FigureBouton de Changement d’outilIndications pour le travail Montage de l’outil de polissage FigureBloquer la pièce à travailler Réglage de la vitesse de rotation Figure36 fr Nettoyage Service après-venteEntretien Garantie38 fr Accessoires fournis FigureChoix d’accessoires voir figures 8 40 fr 41 01 130 21 0.book Seite 41 Freitag, 18. Dezember 2009 747 42 fr 41 01 130 21 0.book Seite 43 Freitag, 18. Dezember 2009 747 No utilice esta herramienta eléctrica sin Para su seguridadInstrucciones generales de seguridad 44 es5Servicio 46 es Instrucciones de seguridad especialesCausas del rechazo y advertencias al respecto 48 es Instrucciones de seguridad específicas para el pulidoInflamarse o provocar una explosión Tratamiento de materiales en polvo peligrosos50 es Vibraciones en la mano/brazoFt/s2 11,5 Inseguridad K, Cables de prolongaciónUtilización reglamentaria de la herramienta eléctrica Symbole52 es Lesionarse Simbolo DefiniciónMortal Tar lesiones graves o mortales54 es Descripción técnica y especificacionesSentarse en caso de una puesta en marcha involuntaria Cubierta Tornillo Instrucciones de montajeMontaje de la empuñadura adicional Figura Montaje de la cubierta de agarre FiguraConexión y desconexión Figura Cambio de útilInstrucciones para la operación Montaje del accesorio para pulir FiguraSujeción de la pieza de trabajo Ajuste de las revoluciones FiguraServicio técnico MantenimientoGarantía Protección del medio ambiente, eliminaciónEmpuñadura adicional Llave allen Palanca de fijación rápida Figura60 es Accesorios disponibles ver figuras 841 01 130 21 0 ES US Seite 61 Freitag, 18. Dezember 2009 837 62 es 41 01 130 21 0 ES US Seite 63 Freitag, 18. Dezember 2009 837 64 es

WPO14-25E, WPO14-15E specifications

FEIN Power Tools, renowned for their precision and quality, offers two remarkable angle grinders: the WPO14-15E and WPO14-25E. These tools are designed for both professional tradespeople and DIY enthusiasts, providing exceptional performance and durability in a variety of applications.

The WPO14-15E is powered by a robust 1500-watt motor that delivers outstanding grinding and cutting capabilities. Its lightweight design, coupled with an ergonomic handle, ensures user comfort during prolonged use. The variable speed control allows for optimal adjustment in relation to the material being processed, making it suitable for a wide range of tasks, from metalworking to masonry.

One of the standout features of the WPO14-15E is the integrated anti-vibration technology, which significantly reduces hand-arm vibrations. This not only enhances user comfort but also extends tool life by minimizing wear and tear. Additionally, the tool's protective guard can be adjusted without the need for tools, allowing for quick and easy modifications to suit specific jobs.

On the other hand, the WPO14-25E takes performance to the next level with a powerful 2500-watt motor, making it ideal for heavy-duty applications. Its robust construction is designed to withstand the rigors of industrial use, providing both longevity and reliability. The WPO14-25E also features advanced electronic controls, including a speed stabilization system that maintains consistent RPMs under load, ensuring precise results.

Both models share similar design characteristics that emphasize user safety and convenience. The quick-change system for the grinding discs allows for rapid swapping, saving valuable time on the job. Furthermore, the specially designed air intake system ensures efficient cooling, preventing overheating during extended use.

In terms of build quality, FEIN's WPO14-15E and WPO14-25E are equipped with superior materials that resist external damage, enabling them to perform effectively in challenging environments. Their compact size and lightweight design facilitate maneuverability, making them easy to handle even in tight spaces.

In summary, the FEIN WPO14-15E and WPO14-25E angle grinders exemplify high-performance engineering, providing users with exceptional comfort, control, and efficiency. With their advanced technologies and thoughtful features, these tools are an excellent investment for anyone seeking reliable power tools for a variety of grinding and cutting applications. Whether for professional or personal use, FEIN delivers unmatched quality and performance with these outstanding angle grinders.