Makita 4351CT, 4351T Operation, Front flush cuts, Bevel cutting, Cutouts, Boring a starting hole

Page 7

CAUTION:

•If you try to remove the dust nozzle forcibly, the hook of the dust nozzle can be diminished and removed unintentionally during operation.

OPERATION

CAUTION:

•

Hold the tool firmly with one hand on the switch

 

handle and the other hand on the front grip when

 

performing the tool.

•

Always hold the base flush with the workpiece.

 

Failure to do so may cause blade breakage,

 

resulting in a serious injury.

 

3

1. Base

1

2. Bolt

 

 

3. Hex wrench

 

 

2

 

 

008013

 

 

Tilt the base until the desired bevel angle is obtained. The V-notch of the gear housing indicates the bevel angle by graduations. Then tighten the bolt firmly to secure the base.

1. Cutting line

2. Base

1

2

008034

Turn the tool on without the blade making any contact and wait until the blade attains full speed. Then rest the

1

 

2

3

 

 

 

4

 

 

 

5

 

6

 

 

 

008014

 

 

 

Front flush cuts

1.Graduation

2.Bevel slot

3.Base

4.Gear housing

5.V-notch

6.Bolt

base flat on the workpiece and gently move the tool forward along the previously marked cutting line.

When cutting curves, advance the tool very slowly.

Bevel cutting

008035

CAUTION:

•Always be sure that the tool is switched off and unplugged before tilting the base.

With the base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right).

Loosen the bolt on the back of the base with the hex wrench. Move the base so that the bolt is positioned in the center of the bevel slot in the base.

 

3

1. Base

 

2. Bolt

1

 

 

3. Hex wrench

 

 

2

 

 

008015

 

 

Loosen the bolt on the back of the base with the hex wrench and slide the base all the way back. Then tighten the bolt to secure the base.

Cutouts

Cutouts can be made with either of two methods A or B.

A) Boring a starting hole:

1. Starting hole

1

008036

For internal cutouts without a lead-in cut from an edge, pre-drill a starting hole 12 mm (1/2") or more in diameter. Insert the blade into this hole to start your cut.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Jig Saw Scie Sauteuse Sierra Caladora English Original instructions SpecificationsMinimum gage for cord Ampere Rating Volts JIG SAW Safety Warnings120 25 ft 50 ft 100 ft 150 ft More Than Not More Than Functional Description Switch actionSelecting the cutting action Lighting up the lamps AssemblySpeed adjusting dial Installing or removing saw bladeAnti-splintering device Cover plate Hex wrench storageDust extraction Cutouts OperationFront flush cuts Bevel cuttingFinishing edges Rip fence set optional accessoryMetal cutting Accessories MaintenanceWarranty Policy Spécifications Français Mode d’emploi originalQue celles prévues peut entraîner une situation dangereuse Consignes DE Sécurité Pour LA Scie Sauteuse Conservez CE Mode DemploiCadran de rélage de vitesse Description DU FonctionnementInterrupteur Sélection du mouvement de coupeAllumage de la lampe AssemblagePose et retrait de la lame de scie Plaque de recouvrement UtilisationRangement de la clé hexagonale Dispositif anti-fentePerçage dun trou de départ Coupes à ras vers lavantCoupe en biseau DécoupageCoupes rectilignes Ensemble de garde parallèle accessoire en optionFinition des bords Coupe du métalEntretien AccessoiresPolitique de garantie Español Instrucciones originales EspecificacionesSeguridad eléctrica Servicio de mantenimiento 12 a Advertencias DE Seguridad Para LA Sierra CaladoraGuarde Estas Instrucciones Más de No más de Calibre del cable AWG 10 aControl de ajuste de velocidad Descripción DEL FuncionamientoAccionamiento del interruptor Selección de corteEncendido de la lámpara EnsambleInstalación o extracción del disco de sierra Almacenamiento de la llave de Allen hexagonal OperaciónDispositivo antiastillado Extracción de polvo Perforando de un agujero de inicio Cortes a ras frontalesCorte en bisel RecortesCortes rectos Acabado de bordesCorte de metales Conjunto de guía de corte al hilo accesorio opcionalAccesorios MantenimientoPolítica de garantía Advertencia

4351CT, 4351T, 4351FCT specifications

The Makita 4351FCT, 4351T, and 4351CT are powerful and efficient tools designed for professional woodworkers and DIY enthusiasts alike. Each model features an array of advanced technologies and robust characteristics that set them apart in the market.

One of the standout features of these jigsaws is the variable speed control that allows users to adjust the speed of the blade between 800 and 2,800 strokes per minute. This flexibility makes it easy to tailor the speed to suit different materials and types of cuts. The saws are equipped with a powerful 720W motor, providing sufficient power for cutting through various materials, including wood, plastic, and metal.

The 4351 series incorporates a patented tool-less blade change system, which simplifies the process of swapping out blades. This feature enhances productivity by allowing users to change blades quickly without the need for additional tools. The saws also support a wide variety of blade types, granting excellent versatility while tackling different projects.

Another remarkable characteristic is the built-in LED light that illuminates the cutting line, ensuring accuracy even in poorly lit work environments. Additionally, the dust blower function keeps the cutting line clear from debris, providing better visibility and cleaner cuts.

In terms of design, the Makita 4351FCT, 4351T, and 4351CT all feature an ergonomic grip that enhances comfort during prolonged use. The saw's rubberized grip reduces vibrations, minimizing fatigue and enabling more precise control. The adjustable base plate allows for bevel cuts of up to 45 degrees, giving users the ability to execute intricate designs effortlessly.

All models in the 4351 series come with a 3-year limited warranty, reflecting Makita's commitment to quality and durability. They are designed to withstand the rigors of daily use, making them a reliable choice for professionals in construction, carpentry, and renovation.

When it comes to performance, the Makita 4351FCT, 4351T, and 4351CT lead the pack with their exceptional cutting speed, precision, and ease of use. Whether you are a seasoned professional or a hobbyist, these jigsaws are perfect for achieving outstanding results in any woodworking project.
Top Page Image Contents