Ryobi P500 SAW Blades, Blade Guard System, STARTING/STOPPING the SAW, LOCK-OFF Button Switch

Page 13

OPERATION

SAW BLADES

The best of saw blades will not cut efficiently if they are not kept clean, sharp, and properly set. Using a dull blade will place a heavy load on the saw and increase the danger of kickback. Keep extra blades on hand, so that sharp blades are always available.

Gum and wood pitch hardened on blades will slow the saw down. Remove saw blade from the saw and use gum and pitch remover, hot water, or kerosene to remove these ac- cumulations. DO NOT USE GASOLINE.

BLADE GUARD SYSTEM

See Figure 9.

The lower blade guard attached to your circular saw is there for your protection and safety. Do not alter it for any reason. If it becomes damaged, do not operate the saw until you have the guard repaired or replaced. Always leave guard in operating position when using the saw.

DANGER:

When sawing through work, lower blade guard does not cover blade on the underside of work. Since blade is exposed on underside of work, keep hands and fingers away from cutting area. Any part of your body coming in contact with moving blade will result in serious injury.

CAUTION:

Never use saw when guard is not operating correctly. Check the guard for correct operation before each use. The guard is operating correctly when it moves freely and readily returns to the closed position. If you drop the saw, check the lower blade guard and bumper for damage at all depth settings before reuse.

LOWER BLADE GUARD

IS IN UP POSITION

WHEN MAKING A CUT

BLADE EXPOSED ON

Fig. 9

UNDERSIDE OF WORKPIECE

 

 

LOCK-OFF

 

BUTTON

SWITCH

 

Fig. 10

STARTING/STOPPING THE SAW

See Figure 10.

To start the saw: Depress the switch trigger.

Always let the blade reach full speed, then guide the saw into the workpiece.

WARNING:

The blade coming in contact with the workpiece before it reaches full speed could cause the saw to “kickback” towards you resulting in serious injury.

To stop the saw: Release the switch trigger.

After you release the switch trigger, allow the blade to come to a complete stop. Do not remove the saw from the

workpiece while the blade is moving.

LOCK-OFF BUTTON

See Figure 10.

The lock-off button reduces the possibility of accidental starting. The lock-off button is located on the handle above the switch trigger. The lock-off button must be depressed before you pull the switch trigger. The lock resets each time the trigger is released.

NOTE: You can depress the lock-off button from either the left or right side.

13

Image 13
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyElectrical Safety General Safety RulesPersonal Safety Work AreaService Specific Safety RulesCauses and Operator Prevention of Kickback Laser Guide Warnings Additional Safety RulesName DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Product Specifications FeaturesAssembly Removing the Blade Attaching the BladeRemoving the Battery Pack Installing the Battery PackDepress Latches to Remove Battery Pack Install OperationWrong KickbackSee Figures 5 Kickback Blade SET TOO Deep Incorrect SupportSAW Blades LOCK-OFF Button SwitchBlade Guard System STARTING/STOPPING the SAWUsing the Laser Guide Adjusting Blade DepthTo Raise SAW Base Assembly Depth To Adjustment Loosen Knob Laser Guide Switch ON/OFFSee Figures 13 Operating the SAWWrong RIP Cutting Cross CUTTING/RIP CuttingTOP View of SAW Guideline Blade Guide Notch Edge ClampBevel Cutting Adjusting the Bevel SettingMaking a Bevel CUT See Figures 19Pocket CUT Lower Blade Guard Pocket CuttingAdjusting Positive 0 Bevel Stop AdjustmentsAdjusting the Laser Positive 0 Bevel StopGeneral Maintenance MaintenanceReplacing Laser Guide Batteries Battery Pack Removal and Preparation for Recycling AccessoriesBatteries Parts and Service Conserver CE Manuel Pour Future Référence Manuel D’UTILISATIONTable DES Matières GarantieAvertissement !  Règles DE Sécurité GénéralesDépannage Règles DE Sécurité ParticulièresCauses DU Rebond ET Précautions À Prendre Mises en garde concernant le guide laser Règeles Supplémentaires Pour LA Sécurité DU FonctionnementSymbole NOM Désignation / Explication SymbolesAVERTISSEMENT  Symbole Signal SignificationAvertissement Fiche Technique CaractéristiquesAssemblage Retrait DE LA Lame Installation DE LA LameUtilisation Installation DU Bloc DE BATTERIES Retrait DU Bloc DE BATTERIES  ApplicationsIncorrect RebondVoir les figures 5 à Système DE Garde DE Lame Lames DE ScieMise EN Marche ET Arrêt DE LA Scie Utilisation DU Guide Laser Réglage DE LA Profondeur DE CoupePour Relever LA Lame Base PourVoir les figures 13 à Utilisation DE LA ScieRefente Coupe Transversale ET RefenteRéglage D’ANGLE DE Biseau Coupe EN BiseauVoir les figures 19 à Bouton DE Réglage DE BiseauÉvidement Garde DE Lame ÉvidementsButée Fixe DE Biseau À RéglagesVérification DE LA Butée Fixe DE Biseau À Réglage DE LA Butée Fixe DE Biseau ÀEntretien Remplacement DES Piles DU Guide LaserEntretien Général Retrait ET Préparation DU Batteries Pour LE Recyclage AccessoiresPièces ET Service Guarde Este Manual Para Futuras Consultas Manual DEL OperadorIntroducción Índice DE ContenidoGarantía ¡ADVERTENCIA Reglas DE Seguridad GeneralesSeguridad Eléctrica Seguridad PersonalServicio Reglas DE Seguridad EspecíficasCausas Y Prevención DE Contragolpes Advertencias relacionadas con la guía láser Reglas Importantes Para LAS Productos DE BateríasSímbolo Nombre DENOMINACIÓN/EXPLICACIÓN SímbolosPrecaución PeligroServicio Advertencia Símbolo Señal SignificadoEspecificaciones DEL Producto CaracterísticasArmado Desmontaje DE LA Hoja DE Corte Montaje DE LA HojaPara Aflojar Para Apretar Aplicaciones FuncionamientoInstalación DEL Paquete DE Baterías Desmontaje DEL Paquete DE BateríasForma Incorrecta ContragolpeSistema DE Protección DE LA Hoja Hojas DE LA SierraEncendido Y Apagado DE LA Sierra InterruptorUtilización DE LA Guía Láser Ajuste DE LA Profundidad DE LA HojaPara Subir LA Sierra Conjunto DE LA Base Interruptor DE LA Guía Láser ENC./ ApagVea las figuras 13 a Utilización DE LA SierraForma Incorrecta Cortes AL Hilo Cortes Transversales Y AL HiloAjuste DEL Ángulo DE Bisel Corte a BiselForma DE Efectuar Cortes a Bisel Vea las figuras 19 aCorte EN Cavidad Tope DE Bisel a AjustesRevisión DEL Tope DE Bisel a Ajuste DEL Tope DE Bisel aMantenimiento General MantenimientoReemplazo DE LAS Baterías DE LA Guía Láser Baterías AccesoriosNotas Notas ONE World TECHNOLOGIES, INC Piezas DE Repuesto Y Servicio
Related manuals
Manual 24 pages 641 b Manual 68 pages 55.09 Kb