Ryobi P500 manual General Maintenance, Replacing Laser Guide Batteries

Page 20

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING:

Always wear safety goggles or safety glasses with side shields during power product operation or when blowing dust. If operation is dusty, also wear a dust mask.

WARNING:

To avoid serious personal injury, always remove the battery pack from the product when cleaning or performing any maintenance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

Only the parts shown on the parts list are intended to be

 

repaired or replaced by the customer. All other parts should

Fig. 25

be replaced at an Authorized Service Center.

 

REPLACING LASER GUIDE BATTERIES

See Figure 25.

Remove the battery pack from the saw.

Make sure the laser is turned off.

Remove the laser cover by lifting it off its base.

Remove both AAA batteries.

Install the two AAA batteries, aligning the positives (+) with positives (+) and the negatives (-) with negatives (-) as shown on the inside base of the laser.

Replace the laser cover.

Turn on the laser.

CAUTION:

Use of controls or adjustments or performance other than those specified herein may result in hazardous radiation exposure.

20

Image 20
Contents OPERATOR’S Manual Save this Manual for Future ReferenceWarranty IntroductionGeneral Safety Rules Electrical SafetyPersonal Safety Work AreaCauses and Operator Prevention of Kickback Specific Safety RulesService Additional Safety Rules Laser Guide WarningsSymbols Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Features Product SpecificationsAssembly Attaching the Blade Removing the BladeInstalling the Battery Pack Removing the Battery PackDepress Latches to Remove Battery Pack Install OperationKickback WrongSee Figures 5 Kickback Blade SET TOO Deep Incorrect SupportLOCK-OFF Button Switch SAW BladesBlade Guard System STARTING/STOPPING the SAWAdjusting Blade Depth Using the Laser GuideTo Raise SAW Base Assembly Depth To Adjustment Loosen Knob Laser Guide Switch ON/OFFWrong Operating the SAWSee Figures 13 Cross CUTTING/RIP Cutting RIP CuttingTOP View of SAW Guideline Blade Guide Notch Edge ClampAdjusting the Bevel Setting Bevel CuttingMaking a Bevel CUT See Figures 19Pocket Cutting Pocket CUT Lower Blade GuardAdjustments Adjusting Positive 0 Bevel StopAdjusting the Laser Positive 0 Bevel StopReplacing Laser Guide Batteries MaintenanceGeneral Maintenance Batteries AccessoriesBattery Pack Removal and Preparation for Recycling Parts and Service Manuel D’UTILISATION Conserver CE Manuel Pour Future RéférenceGarantie Table DES MatièresRègles DE Sécurité Générales Avertissement ! Causes DU Rebond ET Précautions À Prendre Règles DE Sécurité ParticulièresDépannage Règeles Supplémentaires Pour LA Sécurité DU Fonctionnement Mises en garde concernant le guide laserSymboles Symbole NOM Désignation / ExplicationAvertissement Symbole Signal SignificationAVERTISSEMENT  Caractéristiques Fiche TechniqueAssemblage Installation DE LA Lame Retrait DE LA LameInstallation DU Bloc DE BATTERIES  UtilisationRetrait DU Bloc DE BATTERIES  ApplicationsVoir les figures 5 à RebondIncorrect Mise EN Marche ET Arrêt DE LA Scie Lames DE ScieSystème DE Garde DE Lame Réglage DE LA Profondeur DE Coupe Utilisation DU Guide LaserPour Relever LA Lame Base PourUtilisation DE LA Scie Voir les figures 13 àCoupe Transversale ET Refente RefenteCoupe EN Biseau Réglage D’ANGLE DE BiseauVoir les figures 19 à Bouton DE Réglage DE BiseauÉvidements Évidement Garde DE LameRéglages Butée Fixe DE Biseau ÀVérification DE LA Butée Fixe DE Biseau À Réglage DE LA Butée Fixe DE Biseau ÀEntretien Général Remplacement DES Piles DU Guide LaserEntretien Accessoires Retrait ET Préparation DU Batteries Pour LE RecyclagePièces ET Service Manual DEL Operador Guarde Este Manual Para Futuras ConsultasGarantía Índice DE ContenidoIntroducción Reglas DE Seguridad Generales ¡ADVERTENCIASeguridad Eléctrica Seguridad PersonalCausas Y Prevención DE Contragolpes Reglas DE Seguridad EspecíficasServicio Reglas Importantes Para LAS Productos DE Baterías Advertencias relacionadas con la guía láserSímbolos Símbolo Nombre DENOMINACIÓN/EXPLICACIÓNPeligro PrecauciónServicio Advertencia Símbolo Señal SignificadoCaracterísticas Especificaciones DEL ProductoArmado Para Aflojar Para Apretar Montaje DE LA HojaDesmontaje DE LA Hoja DE Corte Funcionamiento AplicacionesInstalación DEL Paquete DE Baterías Desmontaje DEL Paquete DE BateríasContragolpe Forma IncorrectaHojas DE LA Sierra Sistema DE Protección DE LA HojaEncendido Y Apagado DE LA Sierra InterruptorAjuste DE LA Profundidad DE LA Hoja Utilización DE LA Guía LáserPara Subir LA Sierra Conjunto DE LA Base Interruptor DE LA Guía Láser ENC./ ApagForma Incorrecta Utilización DE LA SierraVea las figuras 13 a Cortes Transversales Y AL Hilo Cortes AL HiloCorte a Bisel Ajuste DEL Ángulo DE BiselForma DE Efectuar Cortes a Bisel Vea las figuras 19 aCorte EN Cavidad Ajustes Tope DE Bisel aRevisión DEL Tope DE Bisel a Ajuste DEL Tope DE Bisel aReemplazo DE LAS Baterías DE LA Guía Láser MantenimientoMantenimiento General Accesorios BateríasNotas Notas Piezas DE Repuesto Y Servicio ONE World TECHNOLOGIES, INC
Related manuals
Manual 24 pages 641 b Manual 68 pages 55.09 Kb