Ryobi P500 manual Adjusting Blade Depth, Using the Laser Guide, To Raise SAW Base Assembly

Page 14

OPERATION

ADJUSTING BLADE DEPTH

See Figure 11.

Always keep correct blade depth setting. The correct blade depth setting for all cuts should not exceed 1/4 in. below the material being cut. More blade depth will increase the chance of kickback and cause the cut to be rough. For more depth of cut accuracy, a scale is located on the upper blade guard.

Loosen the depth adjustment knob.

Determine the desired depth of cut.

Locate the depth of cut scale on the back of the upper blade guard.

Hold the base flat against the workpiece and raise or lower the saw until the indicator mark on bracket aligns with the notch on the blade guard.

Tighten the depth adjustment knob securely.

USING THE LASER GUIDE

See Figure 12.

WARNING:

Do not stare into the laser beam or turn the laser on when the tool is not in use. Failure to heed this warning could result in possible serious personal injury. The laser unit comes from the factory already installed and aligned. If the laser becomes misaligned after time refer to the "Adjustments" section.

NOTE: Make a trial cut on a piece of scrap to ensure laser is aligned. Adjusting the laser may be necessary.

Mark the line to be cut on the workpiece.

Adjust the depth and angle of the cut as needed.

Switch on the laser beam.

Install the battery pack into the tool and start the mo- tor.

NOTE: Do not touch the blade to the workpiece until the saw has reached maximum speed.

Slowly push the saw forward into the workpiece.

NOTE: Keep the laser beam on the marked line on the workpiece for precision cutting.

Once the cut is complete, allow the saw to come to a complete stop before turning off the laser.

TO RAISE

SAW

BASE

ASSEMBLY

TO

TO

LOWER SAW

TIGHTEN

DEPTH

TO ADJUSTMENT

LOOSEN KNOB

Fig. 11

LASER GUIDE

SWITCH

ON/OFF

 

5

345

0

0

2

 

20

 

2

 

Fig. 12

14

Image 14
Contents OPERATOR’S Manual Save this Manual for Future ReferenceWarranty IntroductionPersonal Safety General Safety RulesElectrical Safety Work AreaCauses and Operator Prevention of Kickback Specific Safety RulesService Additional Safety Rules Laser Guide WarningsSymbols Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Features Product SpecificationsAssembly Attaching the Blade Removing the BladeDepress Latches to Remove Battery Pack Install Installing the Battery PackRemoving the Battery Pack OperationSee Figures 5 KickbackWrong Kickback Blade SET TOO Deep Incorrect SupportBlade Guard System LOCK-OFF Button SwitchSAW Blades STARTING/STOPPING the SAWTo Raise SAW Base Assembly Adjusting Blade DepthUsing the Laser Guide Depth To Adjustment Loosen Knob Laser Guide Switch ON/OFFWrong Operating the SAWSee Figures 13 TOP View of SAW Guideline Blade Guide Notch Cross CUTTING/RIP CuttingRIP Cutting Edge ClampMaking a Bevel CUT Adjusting the Bevel SettingBevel Cutting See Figures 19Pocket Cutting Pocket CUT Lower Blade GuardAdjusting the Laser AdjustmentsAdjusting Positive 0 Bevel Stop Positive 0 Bevel StopReplacing Laser Guide Batteries MaintenanceGeneral Maintenance Batteries AccessoriesBattery Pack Removal and Preparation for Recycling Parts and Service Manuel D’UTILISATION Conserver CE Manuel Pour Future RéférenceGarantie Table DES MatièresRègles DE Sécurité Générales Avertissement ! Causes DU Rebond ET Précautions À Prendre Règles DE Sécurité ParticulièresDépannage Règeles Supplémentaires Pour LA Sécurité DU Fonctionnement Mises en garde concernant le guide laserSymboles Symbole NOM Désignation / ExplicationAvertissement Symbole Signal SignificationAVERTISSEMENT  Caractéristiques Fiche TechniqueAssemblage Installation DE LA Lame Retrait DE LA LameRetrait DU Bloc DE BATTERIES  Installation DU Bloc DE BATTERIES Utilisation ApplicationsVoir les figures 5 à RebondIncorrect Mise EN Marche ET Arrêt DE LA Scie Lames DE ScieSystème DE Garde DE Lame Pour Relever LA Lame Base Réglage DE LA Profondeur DE CoupeUtilisation DU Guide Laser PourUtilisation DE LA Scie Voir les figures 13 àCoupe Transversale ET Refente RefenteVoir les figures 19 à Coupe EN BiseauRéglage D’ANGLE DE Biseau Bouton DE Réglage DE BiseauÉvidements Évidement Garde DE LameVérification DE LA Butée Fixe DE Biseau À RéglagesButée Fixe DE Biseau À Réglage DE LA Butée Fixe DE Biseau ÀEntretien Général Remplacement DES Piles DU Guide LaserEntretien Accessoires Retrait ET Préparation DU Batteries Pour LE RecyclagePièces ET Service Manual DEL Operador Guarde Este Manual Para Futuras ConsultasGarantía Índice DE ContenidoIntroducción Seguridad Eléctrica Reglas DE Seguridad Generales¡ADVERTENCIA Seguridad PersonalCausas Y Prevención DE Contragolpes Reglas DE Seguridad EspecíficasServicio Reglas Importantes Para LAS Productos DE Baterías Advertencias relacionadas con la guía láserSímbolos Símbolo Nombre DENOMINACIÓN/EXPLICACIÓNServicio Advertencia PeligroPrecaución Símbolo Señal SignificadoCaracterísticas Especificaciones DEL ProductoArmado Para Aflojar Para Apretar Montaje DE LA HojaDesmontaje DE LA Hoja DE Corte Instalación DEL Paquete DE Baterías FuncionamientoAplicaciones Desmontaje DEL Paquete DE BateríasContragolpe Forma IncorrectaEncendido Y Apagado DE LA Sierra Hojas DE LA SierraSistema DE Protección DE LA Hoja InterruptorPara Subir LA Sierra Conjunto DE LA Base Ajuste DE LA Profundidad DE LA HojaUtilización DE LA Guía Láser Interruptor DE LA Guía Láser ENC./ ApagForma Incorrecta Utilización DE LA SierraVea las figuras 13 a Cortes Transversales Y AL Hilo Cortes AL HiloForma DE Efectuar Cortes a Bisel Corte a BiselAjuste DEL Ángulo DE Bisel Vea las figuras 19 aCorte EN Cavidad Revisión DEL Tope DE Bisel a AjustesTope DE Bisel a Ajuste DEL Tope DE Bisel aReemplazo DE LAS Baterías DE LA Guía Láser MantenimientoMantenimiento General Accesorios BateríasNotas Notas Piezas DE Repuesto Y Servicio ONE World TECHNOLOGIES, INC
Related manuals
Manual 24 pages 641 b Manual 68 pages 55.09 Kb