Ryobi P500 manual Parts and Service

Page 22

OPERATOR’S MANUAL

5-1/2 in., 18 VOLT LASER CIRCULAR SAW

P500

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

PARTS AND SERVICE

Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate.

• MODEL NUMBER

P500

 

SERIAL NUMBER

HOW TO OBTAIN REPLACEMENT PARTS:

Replacement parts can be purchased online at www.ryobitools.com or by calling 1-800-525-2579. Replacement parts can also be obtained at one of our Authorized Service Centers.

HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:

Authorized Service Centers can be located online at www.ryobitools.com or by calling 1-800-525-2579.

HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:

To obtain Customer or Technical Support please contact us at 1-800-525-2579.

RYOBI® is a registered trademark of Ryobi Limited used under license.

ONE WORLD TECHNOLOGIES, INC.

1428 Pearman Dairy Road, Anderson, SC 29625

Phone 1-800-525-2579 www.ryobitools.com

983000-496

7-29-10 (REV:06)

22

Image 22
Contents OPERATOR’S Manual Save this Manual for Future ReferenceWarranty IntroductionPersonal Safety General Safety RulesElectrical Safety Work AreaService Specific Safety RulesCauses and Operator Prevention of Kickback Additional Safety Rules Laser Guide WarningsSymbols Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Features Product SpecificationsAssembly Attaching the Blade Removing the BladeDepress Latches to Remove Battery Pack Install Installing the Battery PackRemoving the Battery Pack OperationSee Figures 5 KickbackWrong Kickback Blade SET TOO Deep Incorrect SupportBlade Guard System LOCK-OFF Button SwitchSAW Blades STARTING/STOPPING the SAWTo Raise SAW Base Assembly Adjusting Blade DepthUsing the Laser Guide Depth To Adjustment Loosen Knob Laser Guide Switch ON/OFFSee Figures 13 Operating the SAWWrong TOP View of SAW Guideline Blade Guide Notch Cross CUTTING/RIP CuttingRIP Cutting Edge ClampMaking a Bevel CUT Adjusting the Bevel SettingBevel Cutting See Figures 19Pocket Cutting Pocket CUT Lower Blade GuardAdjusting the Laser AdjustmentsAdjusting Positive 0 Bevel Stop Positive 0 Bevel StopGeneral Maintenance MaintenanceReplacing Laser Guide Batteries Battery Pack Removal and Preparation for Recycling AccessoriesBatteries Parts and Service Manuel D’UTILISATION Conserver CE Manuel Pour Future RéférenceGarantie Table DES MatièresRègles DE Sécurité Générales Avertissement ! Dépannage Règles DE Sécurité ParticulièresCauses DU Rebond ET Précautions À Prendre Règeles Supplémentaires Pour LA Sécurité DU Fonctionnement Mises en garde concernant le guide laserSymboles Symbole NOM Désignation / ExplicationAVERTISSEMENT  Symbole Signal SignificationAvertissement Caractéristiques Fiche TechniqueAssemblage Installation DE LA Lame Retrait DE LA LameRetrait DU Bloc DE BATTERIES  Installation DU Bloc DE BATTERIES Utilisation ApplicationsIncorrect RebondVoir les figures 5 à Système DE Garde DE Lame Lames DE ScieMise EN Marche ET Arrêt DE LA Scie Pour Relever LA Lame Base Réglage DE LA Profondeur DE CoupeUtilisation DU Guide Laser PourUtilisation DE LA Scie Voir les figures 13 àCoupe Transversale ET Refente RefenteVoir les figures 19 à Coupe EN BiseauRéglage D’ANGLE DE Biseau Bouton DE Réglage DE BiseauÉvidements Évidement Garde DE LameVérification DE LA Butée Fixe DE Biseau À RéglagesButée Fixe DE Biseau À Réglage DE LA Butée Fixe DE Biseau ÀEntretien Remplacement DES Piles DU Guide LaserEntretien Général Accessoires Retrait ET Préparation DU Batteries Pour LE RecyclagePièces ET Service Manual DEL Operador Guarde Este Manual Para Futuras ConsultasIntroducción Índice DE ContenidoGarantía Seguridad Eléctrica Reglas DE Seguridad Generales¡ADVERTENCIA Seguridad PersonalServicio Reglas DE Seguridad EspecíficasCausas Y Prevención DE Contragolpes Reglas Importantes Para LAS Productos DE Baterías Advertencias relacionadas con la guía láserSímbolos Símbolo Nombre DENOMINACIÓN/EXPLICACIÓNServicio Advertencia PeligroPrecaución Símbolo Señal SignificadoCaracterísticas Especificaciones DEL ProductoArmado Desmontaje DE LA Hoja DE Corte Montaje DE LA HojaPara Aflojar Para Apretar Instalación DEL Paquete DE Baterías FuncionamientoAplicaciones Desmontaje DEL Paquete DE BateríasContragolpe Forma IncorrectaEncendido Y Apagado DE LA Sierra Hojas DE LA SierraSistema DE Protección DE LA Hoja InterruptorPara Subir LA Sierra Conjunto DE LA Base Ajuste DE LA Profundidad DE LA HojaUtilización DE LA Guía Láser Interruptor DE LA Guía Láser ENC./ ApagVea las figuras 13 a Utilización DE LA SierraForma Incorrecta Cortes Transversales Y AL Hilo Cortes AL HiloForma DE Efectuar Cortes a Bisel Corte a BiselAjuste DEL Ángulo DE Bisel Vea las figuras 19 aCorte EN Cavidad Revisión DEL Tope DE Bisel a AjustesTope DE Bisel a Ajuste DEL Tope DE Bisel aMantenimiento General MantenimientoReemplazo DE LAS Baterías DE LA Guía Láser Accesorios BateríasNotas Notas Piezas DE Repuesto Y Servicio ONE World TECHNOLOGIES, INC
Related manuals
Manual 24 pages 641 b Manual 68 pages 55.09 Kb