Black & Decker CS1015 Additional safEty instructions, Lower guard safety instructions

Page 4

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:

a)Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces. Position your body to either side of the blade, but not in line with the blade. Kickback could cause the saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions are taken.

b)When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

c)When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or kickback from the workpiece as the saw is restarted.

d)Support large panels to minimize the risk of blade pinching and kickback.

Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

e)Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback.

f)Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.

g)Use extra caution when making a “plunge cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.

Lower guard safety instructions

a)Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.

b)Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be

serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.

c)Lower guard should be retracted manually only for special cuts such as “plunge cuts” and “compound cuts.” Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically.

d)Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.

Additional safEty instructions

Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

Keep your body positioned to either side of the blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards (see Causes and

Operator Prevention of Kickback and KICKBACK).

Avoid cutting nails. Inspect for and remove all nails from lumber before cutting.

Always make sure nothing interferes with the movement of the lower blade guard.

Accessories must be rated for at

least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. Accessory ratings must always be above tool speed as shown on tool nameplate.

Always make sure the saw is clean before using.

Stop using this saw and have it properly serviced if any unusual noise or abnormal operation occurs.

Always be sure all components are mounted properly and securely before using tool.

Always handle the saw blade with care when mounting or removing it or when removing the diamond knockout.

Always wait until the motor has reached full speed before starting a cut.

Always keep handles dry, clean and free

of oil and grease. Hold the tool firmly with both hands when in use.

Always be alert at all times, especially during repetitive, monotonous operations.

4

Image 4
Contents 4 184mm, 15 AMP Circular Saw To register your new product, visitGeneral Power tool Safety warnings Keep children and bystandersSafety instructionS for all saws Causes and operator Prevention of kickbackAdditional safEty instructions Lower guard safety instructionsLabel on your tool may include Definitions are as followsVolts MilliwattsKeep blades sharp and clean Always secure work to prevent workpiece movement during cutMotor Intended USEAssembly / adjustment set-p Adjusting the depth of cutOverview fig Attaching the bladeOperation SwitchGuard Against Kickback Maintenance AccessoriesService Information Full Two-Year Home Use WarrantyProblem Possible Cause Possible Solution Serviced at a Black+DeckerService center or authorized Unit will not start Cord not pluggedScie circulaires 7-1/4 184mm, 15 Ampère Règles Générales DE Sécurité Pourtouteslesscies Ne pas passer les mains sous la pièceLes performances et la sécurité de fonctionnement Causes de l’effet de Rebond et preévention Par L’opérateurOu produire un rebond au redémarrage de la scie Directives de Sécurité Supplémentaires scies Circulaires Pour Réduire LE Risque ’EFFET DE Rebond Serrer fermement la scie avec les deux mains en tout tempsGarder les lames aiguisées et propres MoteurAperçu Général fig Configuration de ’assemblage et des RéglagesUtilisation Prévue Fonctionnement Découpes Générales ImportantPROTÉGEZ-VOUS DES Effets DE Rebond InterrupteurAccessoires Découpe EN PocheRangement de la clé EntretienProblème Cause possible Solution possible Sierras circulares de 184mm 7-1/4, 15 amperios Normas Generales DE Seguridad Instruccionesdeseguridad Paratodaslassierras Uso y mantenimiento de la herramienta eléctricaCorte y reduce la posibilidad de que la hoja se atasque Instrucciones De Seguridad para El Protector inferiorTrabajo o producir un retroceso Instrucciones Adicionales Seguridad Manténgase alerta y en control Mantenga las hojas afiladas y limpiasEsto puede provocar Retroceso Retire todos los clavos de la madera antes de cortarDescripción general fig Ensamblado/AjusteUSO Previsto Ajuste de la profundidad de corte yFuncionamiento InterruptorCorte Interno Almacenamiento de la llaveLubricación AccesoriosProblema Causa posible Solución posible Reemplazo gratuito de las Etiquetas de advertencias si susTelephone · No. Teléfono Años DE GarantiaSolamente Para Propositos DE Mexico
Related manuals
Manual 32 pages 34.84 Kb

CS1015 specifications

The Black & Decker CS1015 is a versatile and powerful electric chainsaw designed for both professional and home users. It is recognized for its efficiency, ease of use, and robust performance, making it an ideal tool for cutting through branches, logs, and other types of wood with minimal effort.

One of the standout features of the CS1015 is its 10-inch cutting bar, which is optimized for maneuverability and control. This size is perfect for tackling light to medium-duty tasks, such as trimming trees, clearing fallen branches, or doing yard work. With a powerful 10 amp motor, the chainsaw delivers a high level of performance that allows users to make quick and clean cuts through tough materials.

Safety is a key consideration in the design of the CS1015. It is equipped with a robust safety brake that stops the chain in less than a second if the saw kicks back, providing peace of mind for users who may be new to chainsaw operation. Additionally, the tool features a two-handed grip design that enhances stability and control during operation, reducing the risk of accidents.

The CS1015 also incorporates a tool-free chain tensioning system, making it easier to adjust the chain for optimal performance without needing additional tools. This feature is particularly valuable for users who frequently need to change or adjust the chain during work. Furthermore, the automatic oiler ensures that the chain is adequately lubricated during use, enhancing its longevity and reducing wear.

In terms of weight, the CS1015 is lightweight and easy to handle, allowing users to maneuver it comfortably for extended periods. The electric motor eliminates the need for gasoline, providing a cleaner solution with lower emissions and reduced noise levels compared to gas-powered alternatives. This eco-friendly aspect makes it a great choice for residential areas or any location where noise and fumes could be a concern.

In conclusion, the Black & Decker CS1015 is an impressive electric chainsaw that combines power, safety features, and user-friendly design. It is well-suited for various outdoor tasks while being lightweight and low-maintenance. Whether it's for small projects around the home or more demanding tasks, the CS1015 provides efficiency and reliability that users can depend on.