Bosch Power Tools DDH181XBN Operating Tips, Battery Pack Release Button, Fastening with Screws

Page 12

BM 2610032842 04-14_DDH181X HDH181X 4/9/14 7:10 AM Page 12

INSERTING AND RELEASING BATTERy PACK

Set Forward/Reversing lever to the center (off position). Slide charged battery pack into the housing until the battery pack locks into position (Fig. 12).

Your tool is equipped with a secondary locking latch to prevent the battery pack from completely falling out of the handle, should it become loose due to vibration.

To remove the battery pack, press the battery pack release button and slide the battery pack forward (Fig. 13).

Press the battery pack release button again and slide the battery pack completely out of tool housing (Fig. 13).

FIG. 12

FIG. 13

BATTERY PACK

RELEASE BUTTON

BATTERY PACK

1

2

Operating Tips

You will extend the life of your bits and do neater work if you always put the bit in contact with the work before pulling the trigger. During the oper ation, hold the tool firmly and exert light, steady pressure. Too much pressure at low speed will stall the tool. Too little pressure will keep the bit from cutting and cause excess friction by sliding over the surface. This can be damaging to both tool and bit.

FASTENING WITH SCREWS

This procedure shown in (Fig. 14) will enable you to fasten ma terials together with your Cordless Drill/Screwdriver without stripping, splitting or separating the material.

First, clamp the pieces together and drill the first hole 2/3 the diam eter of the screw. If the material is soft, drill only 2/3 the proper length. If it is hard, drill the entire length.

DRILLING WITH VARIABLE SPEED

The trigger controlled variable speed feature will eliminate the need for center punches in hard materials. The variable speed trigger allows you to slowly increase RPM. By using a slow starting speed, you are able to keep the bit from “wander ng”i. You can increase the speed as the bit “bites” into the work by squeezing the trigger.

DRIVING WITH VARIABLE SPEED

Variable speed drills will double as a power screwdriver by using a screwdriver bit in the drill mode. The technique is to start slowly, increasing the speed as the screw runs down. Set the screw snug yl by slowing to a stop. Prior to driving screws, pilot and

FASTENING

WITH SCREWS

1.  Drill 2/3 diameter and 2/3 of screw length for soft materials, full length for hard materials.

Screw

Apply a slight even pressure when driving screws.

2.  Drill same diameter as screw shank.

3.  Countersink same diameter as screw head.

Adjustable

Screw

Drill

clearance holes should be drilled.

FIG. 14

-12-

Image 12
Contents Call Toll Free for SeeVer la página General Power Tool Safety Warnings Work area safetyElectrical safety Personal safetySafety Rules for Cordless Drill/Drivers Battery tool use and careService Safety Rules for Cordless Hammer Drills Wear ear protectors when impact drillingAdditional Safety Warnings Symbols Symbol Name Designation/ExplanationSymbols Functional Description and Specifications Battery Packs/ChargersCordless Drill/Drivers and Cordless Hammer Drills Model numberAssembly Inserting BitsDrill BIT BIT Holder Screwdriver BIT AUxILIARy HandleVariable Speed Controlled Trigger Switch Operating InstructionsFORWARD/REVERSING Lever & Trigger Lock Gear Shifter Adjustable Clutch Adjustable Clutch DRILL/HAMMER Drill Selector RingMode Selector Ring Brake Gear ShiftingBattery Pack Release Button Operating TipsFastening with Screws Drilling with Variable SpeedWire Brushes Drill BitsDrilling Wood Drilling MetalMaintenance AccessoriesCleaning Sécurité du lieu de travail Sécurité électriqueConsignes de sécurité pour perceuses/tournevis sans cordon Utilisation et entretien des outils ÉlectroportatifsUtilisation et entretien des outils à piles EntretienBM 2610032842 04-14DDH181X HDH181X 4/9/14 710 AM Avertissements supplémentaires concernant la sécurité Le plomb provenant des peintures à base de plombSymboles Symbole Nom Désignation/ExplicationSymboles suite Anneau DE Sélection DE Mode Description fonctionnelle et spécificationsPoignée Caoutchoutée BLOC-PILES Assemblage Insertion DES ForetsConsignes de fonctionnement Levier DE Marche AVANT/ARRIÈRE ET Verrouillage DE GâchetteActive Response Techology Changement DE Vitesses Changement DE Vitesse Embrayage ReglableFrein Éclairage D’APPOINT IntégréConsignes de fonctionnement Forets Perçage DU BoisPerçage DES Métaux Perçage DE LA MaçonnerieAccessoires EntretienNettoyage Seguridad del área de trabajo Seguridad eléctricaUso y cuidado de las herramientas Mecánicas Uso y cuidado de las herramientas Alimentadas por baterías Servicio de ajustes y reparacionesNormas de seguridad para taladros de percusión sin cordón Advertencias de seguridad adicionales Símbolos Símbolo Nombre Designación/explicaciónSímbolos continuación Descripción funcional y especificaciones Número de modeloCapacidades máximas Paquetes de batería/Cargadores de bateríasEnsamblaje Desconecte el paquete deColocacion DE LAS Brocas Instrucciones de funcionamiento Interruptor Gatillo DE Velocidad Variable ControladaPalanca DE AVANCE/INVERSIÓN Y Cierre DEL Gatillo Cambio DE Engranajes Cambiador DE Engranajes Embrague AjustableEmbrague Ajustable Freno LUZ DE Trabajo IncorporadaConsejos de funcionamiento Introducción Y Suelta DEL Paquete DE BateríasSujecion CON Tornillos Brocas Para Taladro Taladrado DE MaderaTaladrado DE Metal Taladrado DE MamposteriaMantenimiento AccesoriosServicio LimpiezaBM 2610032842 04-14DDH181X HDH181X 4/9/14 710 AM Remarques Notas 2610032842