Bosch Power Tools DDH181XBN, DDH181X-01L, DDH181XBL manual Maintenance, Accessories, Cleaning

Page 14
! CAUTION
! WARNING
! WARNING

BM 2610032842 04-14_DDH181X HDH181X 4/9/14 7:10 AM Page 14

RUNNING NUTS AND BOLTS

Variable speed control must be used with caution for driving nuts and bolts with socket set attach ments. The technique is to start slowly, increasing speed as the nut or bolt runs

down. Set the nut or bolt snugly by slowing the drill to a stop. If this procedure is not followed, the tool will have a tendency to torque or twist in your hands when the nut or bolt seats.

Maintenance

Service

NO USER SERVICEABLE

PARTS INSIDE. Preventive maintenance performed by un au thorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recom- mend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station. SERVICE MEN: Disconnect tool and/or charger from power source before servicing.

BATTERIES

Be alert for battery packs that are nearing their end of life. If you notice decreased tool performance or significantly shorter running time between charges then it is time to replace the battery pack. Failure to do so can cause the tool to operate improperly or damage the charger.

TOOL LUBRICATION

Your Bosch tool has been properly lubricated and is ready for use.

MOTOR

The motor in your tool has been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend it be examined every six months. Only a genuine Bosch replacement motor specially designed for your tool should be used.

Cleaning

To avoid accidents, always disconnect the tool and/or charger from the power supply before

cleaning. The tool may be cleaned most effectively with com pressed dry air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through opening.

Certain cleaning agents and solvents damage plastic parts. Some of these are: gasoline,

car bon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

 

Accessories

(* = standard equipment)

*

Screwdriver bit

(** = optional accessories)

*

Carrying case

-14-

Image 14
Contents Ver la página Call Toll Free forSee Electrical safety General Power Tool Safety WarningsWork area safety Personal safetyService Safety Rules for Cordless Drill/DriversBattery tool use and care Safety Rules for Cordless Hammer Drills Wear ear protectors when impact drillingAdditional Safety Warnings Symbols Symbol Name Designation/ExplanationSymbols Cordless Drill/Drivers and Cordless Hammer Drills Functional Description and SpecificationsBattery Packs/Chargers Model numberDrill BIT BIT Holder Screwdriver BIT AssemblyInserting Bits AUxILIARy HandleFORWARD/REVERSING Lever & Trigger Lock Variable Speed Controlled Trigger SwitchOperating Instructions Mode Selector Ring Brake Gear Shifter Adjustable ClutchAdjustable Clutch DRILL/HAMMER Drill Selector Ring Gear ShiftingFastening with Screws Battery Pack Release ButtonOperating Tips Drilling with Variable SpeedDrilling Wood Wire BrushesDrill Bits Drilling MetalCleaning MaintenanceAccessories Sécurité du lieu de travail Sécurité électriqueUtilisation et entretien des outils à piles Consignes de sécurité pour perceuses/tournevis sans cordonUtilisation et entretien des outils Électroportatifs EntretienBM 2610032842 04-14DDH181X HDH181X 4/9/14 710 AM Avertissements supplémentaires concernant la sécurité Le plomb provenant des peintures à base de plombSymboles Symbole Nom Désignation/ExplicationSymboles suite Poignée Caoutchoutée BLOC-PILES Anneau DE Sélection DE ModeDescription fonctionnelle et spécifications Assemblage Insertion DES ForetsActive Response Techology Consignes de fonctionnementLevier DE Marche AVANT/ARRIÈRE ET Verrouillage DE Gâchette Frein Changement DE VitessesChangement DE Vitesse Embrayage Reglable Éclairage D’APPOINT IntégréConsignes de fonctionnement Perçage DES Métaux ForetsPerçage DU Bois Perçage DE LA MaçonnerieNettoyage AccessoiresEntretien Uso y cuidado de las herramientas Mecánicas Seguridad del área de trabajoSeguridad eléctrica Uso y cuidado de las herramientas Alimentadas por baterías Servicio de ajustes y reparacionesNormas de seguridad para taladros de percusión sin cordón Advertencias de seguridad adicionales Símbolos Símbolo Nombre Designación/explicaciónSímbolos continuación Capacidades máximas Descripción funcional y especificacionesNúmero de modelo Paquetes de batería/Cargadores de bateríasColocacion DE LAS Brocas EnsamblajeDesconecte el paquete de Palanca DE AVANCE/INVERSIÓN Y Cierre DEL Gatillo Instrucciones de funcionamientoInterruptor Gatillo DE Velocidad Variable Controlada Embrague Ajustable Freno Cambio DE EngranajesCambiador DE Engranajes Embrague Ajustable LUZ DE Trabajo IncorporadaSujecion CON Tornillos Consejos de funcionamientoIntroducción Y Suelta DEL Paquete DE Baterías Taladrado DE Metal Brocas Para TaladroTaladrado DE Madera Taladrado DE MamposteriaServicio MantenimientoAccesorios LimpiezaBM 2610032842 04-14DDH181X HDH181X 4/9/14 710 AM Remarques Notas 2610032842