![](/images/new-backgrounds/1210151/21015111x1.webp)
90565382 SSL16 SSL20 NEW Smart
KEYLESS CHUCK (FIGURE F) |
|
|
|
| |
WARNING: Make certain the | F |
|
button is engaged to prevent switch actuation |
|
|
before installing or removing accessories. |
|
|
To insert a drill bit or other accessory: |
|
|
1. Grasp the rear half of the chuck (4) with |
|
|
one hand and use your other hand to | 4a | 4 |
rotate the front half (4a) in the | ||
counterclockwise direction, as viewed |
|
|
from the chuck end. |
|
|
2.Insert the bit or other accessory fully into the chuck, and tighten securely by holding
the rear half of the chuck and rotating the front portion in the clockwise direction as
viewed from the chuck end.WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.
SCREW DRIVING
For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first.
ON BOARD BIT STORAGE (FIGURE G)
A bit storage slot (8) is
G
8
DRILLING
•Use sharp drill bits only.
•Support and secure work properly, as instructed in the Safety Instructions.
•Use appropriate and required safety equipment, as instructed in the Safety Instructions.
•Secure and maintain work area, as instructed in the Safety Instructions.
•Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.
•Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.
•Hold the drill firmly with two hands to control its twisting action.
•DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.
•Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.
•Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.
•Make sure switch turns drill on and off.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.
TROUBLESHOOTING
Problem | Possible Cause | Possible Solution |
• Unit will not start. | • Battery pack not installed properly. | • Check battery pack |
| • Battery pack not charged. | installation. |
| • Check battery pack charging | |
• Battery pack will not charge. | • Battery pack not inserted into charger. | requirements. |
• Insert battery pack into | ||
|
| charger until green LED |
| • Charger not plugged in. | appears. |
| • Plug charger into a working | |
|
| outlet. Refer to “Important |
|
| Charging Notes” for more |
| • Surrounding air temperature | details. |
| • Move charger and battery | |
| too hot or too cold. | pack to a surrounding air |
|
| temperature of above 40 |
|
| degrees F (4.5°C) or below |
|
| 105 degrees F (+40.5°C). |
• Unit shuts off abruptly. | • Battery pack has reached its | •Allow battery pack to cool |
| maximum thermal limit. | down. |
| • Out of charge. ( To | • Place on charger and |
| maximize the life of the | allow to charge. |
| batterypackitisdesigned |
|
| to shutoff abruptly when |
|
| the charge is depleted.) |
|
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
THE RBRC™ SEAL The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
Black & Decker. In some areas, it is illegal to place spent
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent
10 | 11 | ||
|
|
|
|
|
|
|
|
|
|
|
|