Western Telematic RSM-16, RSM-32DC manual Secure Racking, Shock Hazard Do Not Enter Lithium Battery

Page 2

Warnings and Cautions:

Installation Instructions

Secure Racking

If Secure Racked units are installed in a closed or multi-unit rack assembly, they may require further evaluation by Certification Agencies. The following items must be considered.

1.The ambient within the rack may be greater than room ambient. Installation should be such that the amount of air flow required for safe operation is not compromised. The maximum temperature for the equipment in this environment is 45°C. Consideration should be given to the maximum rated ambient.

2.Installation should be such that a hazardous stability condition is not achieved due to uneven loading.

Input Supply

1.Check nameplate ratings to assure there is no overloading of supply circuits that could have an effect on overcurrent protection and supply wiring.

2.When installing 48 VDC rated equipment, it must be installed only per the following conditions:

A.Connect the equipment to a 48 VDC supply source that is electrically isolated from the alternating current source. The 48 VDC source is to be connected to a 48 VDC SELV source.

B.Input wiring to terminal block must be routed and secured in such a manner that it is protected from damage and stress. Do not route wiring past sharp edges or moving parts.

C.A readily accessible disconnect device, with a 3 mm minimum contact gap, shall be incorporated in the fixed wiring.

Grounding

Reliable earthing of this equipment must be maintained. Particular attention should be given to supply connections when connecting to power strips, rather than direct connections to the branch circuit.

No Serviceable Parts Inside; Authorized Service Personnel Only

Do not attempt to repair or service this device yourself. Internal components must be serviced by authorized personnel only.

•Shock Hazard - Do Not Enter

•Lithium Battery

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.

i

Image 2

Contents RSM Series Shock Hazard Do Not Enter Lithium Battery Secure RackingDisconnect Power Agency Approvals Table of Contents Configuration Table of Contents List of Figures Intelligent Port Selection Security and Collocation FeaturesIntroduction Capture BufferTypographic Conventions Configuration BackupRSM-8, RSM-16, RSM-16DC, RSM-32 and RSM-32DC Units Bold FontUnit Description Front PanelBack Panel Instrument Back Panel Model RSM-8 Power On/Off Switch Getting Started Quick Hardware InstallationApply Power to the RSM Connect your Control Device to the RSMCommunicating with the RSM Port Status Screen Text Interface RSM-8 Shown Getting Started DC Powered Units Hardware InstallationConnecting Power to the RSM Unit Connecting the Network Cable Connecting Devices to the RSMText Interface ConfigurationCommunicating with the RSM Unit Configuration Web Browser Interface Home Screen Web Browser InterfaceSystem SetUp Ports Configuration MenusDefining System Parameters System ParametersConfiguration Real Time Clock and Calendar Invalid Access Lockout Feature Audit Log Callback Security Configuration User Accounts Supervisor AccessPort Access Managing User Accounts Viewing User AccountsAdding User Accounts Add User Menu Text Interface RSM-8 ShownConfiguration Modifying User Accounts Deleting User AccountsRS232 Port Configuration 1. RS232 Port ModesPort Configuration Menu Text Interface 2. RS232 Port Configuration Menus Communication SettingsGeneral Parameters Port Mode Parameters AT&C1&D2S0=1&B1&H1&R2Network Services Configuring the Internal Modem Network Configuration Servers and ClientsConfiguration Network Parameters 11 Network Parameters Menu Web Browser InterfaceNetwork Port Parameters 12 Network Port Parameters Menu Web Browser InterfaceConfiguration IP Security IP SecurityConfiguration Configuration Except Net/Mask PairsConfiguration Static Route 15 Static Route Menu Text InterfaceDomain Name Server 17 Nomain Name Server Menu Text Interface19 Snmp Access Menu Text Interface Snmp ParametersConfiguration Ldap Parameters LdapConfiguration Group Membership Value Type Default = DN Ldap Group25 Add Ldap Group Menu Text Interface RSM-8 Shown 27 View Ldap Group Menu Text Interface RSM-8 Shown 29 Modify Ldap Group Menu Text Interface RSM-8 Shown 31 Delete Ldap Group Menu Web Browser Interface 32 Ldap Kerberos Set Up Menu Text Interface Configuration Tacacs Parameters 34 The Tacacs Parameters Menu Text InterfaceConfiguration Radius Parameters 36 The Radius Parameters Menu Text InterfaceConfiguration 38 The Copy Port Parameters Menu Save User Selected Parameters CP 3,5,7-9 EnterStatus Screens Port Status Screen /S Status ScreensPort Diagnostics Screen /SD Port Diagnostics Screen RSM-8 ShownNetwork Status Screen /SN Porttcp Portstatus UsernamePort Parameters Screens /W Port Parameters Screen RS232 Port ShownXx Enter Port Connection and Disconnection Any-to-Any ModeOperation Operation Operation 4 Enter EnterDefining Hunt Groups Hunt Group ExamplePassive Mode Buffer Mode Reading Data from Buffer Mode PortsPort Buffers Modem Mode SSH Encryption Telnet & SSH FunctionsNetwork Port Numbers Standard Telnet Protocol, SSH and Raw Socket Direct Connect FeatureConfiguration Telnet & SSH Functions RSM-16 & RSM-16DC Standard Telnet Direct Connection without Password RSM-8SSH Direct Connection with Password RSM-8 RSM-32 & RSM-32DCConnection Example Raw Socket Direct Connection with Password RSM-8Raw Socket Direct Connection without Password RSM-8 Terminating a Direct Connect Session Syslog Feature ConfigurationCriteria for Generating a Syslog Message Testing Syslog Configuration Test Menu Text Interface, Supervisor Mode OnlySnmp Traps 10-1Snmp Contact Optional Snmp Location Optional How and When Snmp Traps are SentSnmp Trap Message Testing the Snmp Trap Function Saving and Restoring Configuration Parameters Sending Parameters to a FileRestoring Saved Parameters Upgrading RSM Firmware 12-112-2 Command Reference Guide Command ConventionsCommand Summary Audit Log Command SetResident Disconnect Sequence CP Copy RS232 Port Parameters ConnectFormat /C x x Enter Format /CP Enter2 Enter or /D/Y 3 Enter Third Party DisconnectFormat /D/Y x x Enter Erase BufferHelp Reboot System DefaultSet System Parameters Display Site IDSet RS232 Port Parameters Send SSH KeySet Network Port Parameters Read Buffer PW Change PasswordSD Display Port Diagnostics Display Port StatusTest Test Network Parameters UF Upgrade FirmwareUL Unlock Port Invalid Access Lockout Save ParametersFormat /W x Enter Exit Command ModeDisplay Port Parameters Who Format /X EnterAppendix A. RS232 Port Interface When connectedWhen not connected Physical / Environmental Power Appendix B. SpecificationsRS232 Port Interface Connectors Models RSM-32 and RSM-32DCAppendix C. Customer Service Trademark and Copyright Information Trademarks Used in this ManualIndex Tacacs DhcpIndex-2 Index-3 Index-4