Western Telematic RSM-8, RSM-32DC, RSM-16DC Save User Selected Parameters, CP 3,5,7-9 Enter

Page 71

Configuration

2.Invoke the /CP command at the command prompt; the menu shown in Figure 5.38 will be displayed. The following options are available:

a)Copy to All Ports: Type /CP [Enter].

b)Copy to a Range of Ports: Type /CP m-n[Enter]. Where m and n are port numbers that specify the desired range. For example, to copy parameters to ports 3 through 7, type /CP 3-7and press [Enter].

c)Copy to Several Ports: Type /CP m,n,x [Enter]. Where m, n and x are the numbers of the desired ports. For example, to copy parameters to ports 3, 5, and 7, type /CP 3,5,7 [Enter].

d)Combination: To invoke the /CP command in a manner where a range of ports is specified, along with several ports outside the range, type /CP m,n,x-z[Enter]. Where m, n, x, and z are port numbers. For example to copy parameters to ports 3 and 5 plus ports 7 through 9, type

/CP 3,5,7-9 [Enter].

3.Selecting Parameters: To select parameters to be copied, key in the number for the desired parameter, press [Enter], then follow the instructions in the submenu.

Note: The /CP command will only copy the parameters currently displayed by the Copy Port Parameters menu.

4.Clear Menu: After defining several parameters, if you wish to clear the /CP menu and start again, type - (dash) and press [Enter], the menu will be reset.

5.Exit Without Copy: To exit from the Copy Parameters menu without copying selected parameters, type X [Enter]. The RSM will return to the command prompt.

6.Copy Parameters: When you have finished selecting parameters, press [Esc] to copy the selected parameters.

5.10.Save User Selected Parameters

Although this step is optional, it is strongly recommended to save all user-defined parameters to an ASCII file as described in Section 11. This will allow quick recovery in the event of accidental deletion or reconfiguration of port parameters.

5-52

Image 71

Contents RSM Series Secure Racking Shock Hazard Do Not Enter Lithium BatteryDisconnect Power Agency Approvals Table of Contents Configuration Table of Contents List of Figures Capture Buffer Security and Collocation FeaturesIntroduction Intelligent Port SelectionBold Font Configuration BackupRSM-8, RSM-16, RSM-16DC, RSM-32 and RSM-32DC Units Typographic ConventionsFront Panel Unit DescriptionInstrument Back Panel Model RSM-8 Back Panel Power On/Off Switch Connect your Control Device to the RSM Quick Hardware InstallationApply Power to the RSM Getting StartedCommunicating with the RSM Port Status Screen Text Interface RSM-8 Shown Getting Started DC Powered Units Hardware InstallationConnecting Power to the RSM Unit Connecting Devices to the RSM Connecting the Network CableText Interface ConfigurationCommunicating with the RSM Unit Configuration Home Screen Web Browser Interface Web Browser InterfaceConfiguration Menus System SetUp PortsSystem Parameters Defining System ParametersConfiguration Real Time Clock and Calendar Invalid Access Lockout Feature Audit Log Callback Security Configuration User Accounts Supervisor AccessPort Access Viewing User Accounts Managing User AccountsAdd User Menu Text Interface RSM-8 Shown Adding User AccountsConfiguration Deleting User Accounts Modifying User Accounts1. RS232 Port Modes RS232 Port ConfigurationPort Configuration Menu Text Interface Communication Settings 2. RS232 Port Configuration MenusGeneral Parameters AT&C1&D2S0=1&B1&H1&R2 Port Mode ParametersNetwork Services Configuring the Internal Modem Servers and Clients Network ConfigurationConfiguration 11 Network Parameters Menu Web Browser Interface Network Parameters12 Network Port Parameters Menu Web Browser Interface Network Port ParametersConfiguration IP Security IP SecurityConfiguration Configuration Net/Mask Pairs ExceptConfiguration 15 Static Route Menu Text Interface Static Route17 Nomain Name Server Menu Text Interface Domain Name ServerSnmp Parameters 19 Snmp Access Menu Text InterfaceConfiguration Ldap Ldap ParametersConfiguration Ldap Group Group Membership Value Type Default = DN25 Add Ldap Group Menu Text Interface RSM-8 Shown 27 View Ldap Group Menu Text Interface RSM-8 Shown 29 Modify Ldap Group Menu Text Interface RSM-8 Shown 31 Delete Ldap Group Menu Web Browser Interface 32 Ldap Kerberos Set Up Menu Text Interface Configuration 34 The Tacacs Parameters Menu Text Interface Tacacs ParametersConfiguration 36 The Radius Parameters Menu Text Interface Radius ParametersConfiguration 38 The Copy Port Parameters Menu CP 3,5,7-9 Enter Save User Selected ParametersStatus Screens Status Screens Port Status Screen /SPort Diagnostics Screen RSM-8 Shown Port Diagnostics Screen /SDPorttcp Portstatus Username Network Status Screen /SNPort Parameters Screen RS232 Port Shown Port Parameters Screens /WXx Enter Port Connection and Disconnection Any-to-Any ModeOperation Operation Operation Enter 4 EnterHunt Group Example Defining Hunt GroupsPassive Mode Reading Data from Buffer Mode Ports Buffer ModePort Buffers Modem Mode SSH Encryption Telnet & SSH FunctionsNetwork Port Numbers Standard Telnet Protocol, SSH and Raw Socket Direct Connect FeatureConfiguration Telnet & SSH Functions RSM-32 & RSM-32DC Standard Telnet Direct Connection without Password RSM-8SSH Direct Connection with Password RSM-8 RSM-16 & RSM-16DCConnection Example Raw Socket Direct Connection with Password RSM-8Raw Socket Direct Connection without Password RSM-8 Terminating a Direct Connect Session Configuration Syslog FeatureCriteria for Generating a Syslog Message Test Menu Text Interface, Supervisor Mode Only Testing Syslog Configuration10-1 Snmp TrapsSnmp Contact Optional Snmp Location Optional How and When Snmp Traps are SentSnmp Trap Message Testing the Snmp Trap Function Sending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters 12-1 Upgrading RSM Firmware12-2 Command Conventions Command Reference GuideCommand Summary Audit Log Command SetResident Disconnect Sequence Format /CP Enter ConnectFormat /C x x Enter CP Copy RS232 Port ParametersErase Buffer Third Party DisconnectFormat /D/Y x x Enter 2 Enter or /D/Y 3 EnterDisplay Site ID Reboot System DefaultSet System Parameters HelpSet RS232 Port Parameters Send SSH KeySet Network Port Parameters Display Port Status PW Change PasswordSD Display Port Diagnostics Read BufferSave Parameters UF Upgrade FirmwareUL Unlock Port Invalid Access Lockout Test Test Network ParametersFormat /X Enter Exit Command ModeDisplay Port Parameters Who Format /W x EnterAppendix A. RS232 Port Interface When connectedWhen not connected Models RSM-32 and RSM-32DC Appendix B. SpecificationsRS232 Port Interface Connectors Physical / Environmental PowerAppendix C. Customer Service Trademarks Used in this Manual Trademark and Copyright InformationTacacs Dhcp IndexIndex-2 Index-3 Index-4