Bosch Appliances D9412GV3 # Perimeter O/C, # Latest Close Time, # Two Man Rule, Arming Features

Page 47

D9412GV3/D7412GV3 Program Entry Guide 2.0 Panel and Area Wide Parameters

EN 47

A# Perimeter O/C

Default:

No

Selection:

Yes or No

Yes

This area can send Perimeter Opening and

 

Closing Reports.

 

 

No

This area cannot send Perimeter Opening

 

and Closing Reports.

 

 

 

This item determines if this area can send Perimeter Instant and Perimeter Delay Closing Reports and normal Opening Reports to the central station. Opening and Closing Windows do not suppress this event. Refer to the L## Perimeter O/C prompt on page 75.

This reporting requires ModemIIIa2 reporting format reporting. Some central station automation systems cannot process these reports.

A# Latest Close Time

Default: 00:00

Selection: 00:00 to 24:00

Use to set a Latest Close Time boundary value for this area. If the Latest Close Time value is non-zero, the time of day specified with the Extend Close feature cannot be greater than or equal to this value. A zero value for A# Latest Close Time disables the feature for the area.

Example: If A# Latest Close Time is set for 17:30, the user can extend the close time to as late as 17:29.

This prompt is used only when an O/C Window is assigned to an area. Make entries in 30-min increments using a 24-hour format. Use times that begin on the hour or the half-hour only. For example, enter 2:30 PM as 14:30. Enter 1:00 AM as 01:00. To set the Latest Close Time for midnight, use a value of 24:00. The latest close time allowed by the Extend Close feature is 24:58, because of internal limitations in the control panel.

The default entry of 00:00 disables the

Latest Close Time feature for this area.

The control panel sets all windows for the next day when the control panel clock turns to midnight. The control panel must cross the midnight boundary before any changes in that default setting occur.

To extend across midnight, you must use two windows:

To suppress reports before midnight, use one window (for example, 20:00 start to 23:59 stop).

To suppress reports immediately after midnight, use another window (for example, 00:01 start to 02:00 stop).

2.8.5Arming Features

A# Two Man Rule

 

Default:

 

No

 

 

Selection:

 

Yes or No

 

 

Yes

 

Two valid unique passcodes are

 

 

 

 

 

required to disarm the area.

 

 

 

 

 

 

 

No

A single passcode with a valid

 

 

 

 

 

authority level can disarm the area.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The D720 Keypad does not support the

Two-Man Rule feature.

Use this parameter when disarming an area that is Master Armed. After recognizing the first valid passcode, the system requests a second passcode to disarm the area. If the entry delay expires before the entry of a second valid unique passcode, an alarm condition occurs. This function works only when you use Passcode Disarm.

When you are disarming an area with A# Two Man Rule set to Yes, the keypad waits for the time equal to the A# Exit Delay Time. If the second passcode is not entered before the prompt times out, the rule resets and waits for the first passcode again.

If the area is already in an alarm condition, the first valid passcode entered after the alarm occurs silences the bell but does not disarm the area. Enter Code 2 appears on the display. A second valid unique passcode is necessary to disarm the area.

This feature is not allowed for use with SIA CP-01 compliant installations. Consult the local authority having jurisdiction (AHJ) for proper usage. Refer to your control panel’s program entry guide for programming information.

Bosch Security Systems, Inc. 10/11 F01U170807-02

Page 46 Page 48
Image 47
Page 46 Page 48
Contents D9412GV3/D7412GV3 v8.11 and Higher Type Styles Used in this Manual System RequirementsTable of Contents Programming Prompts Directory 148 Tables147 Document Name Part Number Using this Program Entry GuideDifferences between the D9412GV3 and D7412GV3 Features Literature ReferencedGuide to Programming Options D1255 Keypad Programming Menu and Page References D1260 Keypad Programming Menu and Page References Guide to UL 864 Programming Requirements D9412GV3/D7412GV3 Program Entry Guide 1.0 Introduction Recommendation For Ground Fault Enable SwitchUL 864 Programming Recommendations Prompt Possible Settings Phone # For SIA CP-01 Compliance Call Waiting DisablePhone D1260 D1255Phone # Format Default Modem IIIa2 Selection Modem IIIa2 or Contact IDDefault Yes Selection Yes or No Phone ParametersModem IIIa2 Communication Format Data Point Numbers Dtmf DialingD6000 User IDs and Zones Two Phone Lines Alarm On FailPhone Supv Time Buzz on FailRoute Number Groups Which Has the Highest Priority? Default Selection Yes or NoExpand Test Report Called Party DisconnectRouting Destination Communication Failures Programming Primary and Backup DestinationsEnhanced Routing Programming a Duplicate ReportRoute Group 1 4 option # Primary DeviceRoute GRP 1 4 option # Backup Device Burglar Reports Fire ReportsBurglar Reports Fire Reports Selections DescriptionSending Test Reports User ReportsTest Reports User Reports Selections DescriptionTest Reports Selections Description Diagnostics ReportsReport Selections Description Diagnostic ReportsRelay Reports Selections Report DescriptionRPS Reports Selections Report Description Auto Function ReportsRPS Reports Auto-Function Reports Selections Report DescriptionUser Change Reports Selections Description Point ReportsUser Chng Reports Point Reports Selections DescriptionEvent Descriptions, Priorities, and Numbers Access ReportsAccess Reports Selections Report Description Event Descriptions, Priorities, and Numbers Power Supervision Printer Parameters ## Fire Events ## Access Event## Scope ## A1 through A# in ScopeRPS Passcode RPS Parameters## Point Event ## Usr Chng EvtContact RPS if Log % Full Default Selection 0 toLog % Full Answer Armed Default Refer to the program record sheet SelectionRPS Call Back RPS Line MonitorRPS Modem Speed Default Blank Selection Blank or up to 24 charactersDefault Selection 300, 1200 RPS Phone #Area Parameters MiscellaneousArea On to Yes Area# Account Number# Force Arm/Bypass Max # Auto Watch # Delay Restorals# Exit Tone # Exit Dly TimeVerify Time to 60 sec # Duress Enable# Duress Enable must be set to Yes # Area Type Shared Area Arming Sequence Shared-Area Characteristics Arming a Shared AreaAccess Control Readers Assigned to the Shared Area Disarming a Shared Area# Burg Pattern # Fire Time# Fire Pattern # Burg TimeRing # Single Ring# Bell Test # Account O/C # Fail to Open # Disable O/C in Window# Area O/C # Auto CloseExit Dly Time  If Disable O/C in Window is# Fail to Close # Restrictd O/C# Latest Close Time Default Selection 0000 toArming Features # Perimeter O/CD1255 Keypad Parameter Setup RequirementTo Early Ambush Timer on # Early Ambush# Exit Warning must be set to Yes # Exit Restart# Arm No Exit # Exit Warning# Entry Warning must be set to Yes Keypad Command Center# Entry Warning Cmd CenterCC# Area Assign CC# Enhanced Command CenterDefault Selection 1 to 32 on D9412GV3 1 to 8 on D7412GV3 CC# SupervisedSame A# Account Number, CC# ScopeCC# A1 through A# in Scope CC# Assign Door CC# Enter Key RelayCC# Enter Key Cycle Door Trouble Tone to Yes CC# Trouble ToneCC# Entry Tone CC# Exit Tone## Passcode Arm CC# Arm Now WarningCC# Close Door CC# Passcode Follows ScopeCC# Abort Display CC# Cancel DisplayCC# Scroll Lock CC# Menu Key LockArea# Account Is On Area# Is OnArea# Not Ready Area# Is OffSee .9.2 Area Text on Custom FunctionCF### Text CF### Key StrokesExample User InterfacePerimeter Instant Master Arm DelayMaster Arm Instant View Area Stat Perimeter DelayWatch Mode Perimeter PartialDoor Control Access Ctl LevelView Point Status Walk TestExtend Close Change Time/DateChange Passcode Del UserUnbypass a Point Bypass a PointPrint Log User CmdRemote Program Reset SensorsService Walk Change RelayFunction 128 through Default TextChange Skeds Invisible Walk Test## Disarm Default Selection 1 toDefault Refer to the program record sheet Selection Or E Authority Level## Master Arm Instant ## Master Arm Delay## Perimeter Delay ## Watch Mode## Fire Test ## View Memory## View Point Status ## Walk Test## Unlock Door ## Send Report## Door Control ## Cycle Door## Change Passcode ## Access Control Level## Change Display ## Change Time/Date## View Log ## Add User## Del User ## Extend Close## Change Relay ## Reset Sensors## Service Walk ## Bypass a Point## Invisible Walk Test ## Default Text## Change Skeds ## Area O/C ## C Function 128 through## Force Arm ## Passcode Arm## Function Level Default Refer to the program record sheet Selection C, or## Disarm Level ## Function Function ListMenu Item ## CC Address 1 through Relay ParametersArea Relays # Alarm Bell# Reset Sensors # Fire Bell# Force Armed # Fail to Close # Watch Mode# Area Fault # Area ArmedAC Failure # Perimeter Fault# Silent Alarm # Duress RelayPasscode or Token Worksheet User Group Window User GroupsPasscodes Passcode TamperUser passcode User token or card Reporting and Logging### User Group Default Selection 0, 1 toUser ### ### Passcode### SU1 through SU3 Site ### Name### Mstr Site ### Mstr Crd Data## Type Point IndexPoint Index ## Type Description On next Program Point Response as Disarmed is YesApplications for Point Responses 9, D, and E Point ResponsesExample of Controlled point ## Entry Delay## Pt Response Hour Points## Audible After 2 Failures ## Ring Until Restored## Entry Tone Off ## Silent Bell## Invisible Point Regardless of the armed state . The buzz ## Buzz On FaultKeypad for any fault condition while the point Point Response## Local While Disarmed ## Watch Point## Relay Response Type ## Display as Device## Force Arm Returnable ## Disable Restorals## Local While Armed A# Auto Close prompt ## Bypass Returnable## Bypassable ## Cross Point ## Swinger Bypass## Report Bypass at Occurrence ## Defer Bypass Report## Fire Point ## Alarm Verify## Resettable Parameter Abort Window ## Alarm AbortPoint Number ### Point Index### Debounce ### Area Assign### Relay Codes/Relays ### Relay### Point Text CMD9 Relay CMD7 Point IndexCMD7 Relay CMD9 Point Index# Sunday WindowsWindow # Thursday # Monday# Tuesday # Wednesday# Open Window Stop Default Selection Hhmm hours and minutesDisable O/C in Window is programmed Yes # Open Window StartProgramming to Link Two Days over Midnight # Close Early Begin# Close Window Stop # Close Window StartHoliday Indexes for O/C Windows # Xept Holiday# Holiday # Area 1 throughNormal Store Hours Opening and Closing Windows WorksheetMonthly Auditor’s Schedule User Windows #UW# User Group Delivery ScheduleUW# Monday UW# Group EnableUW# Group Disable UW# SundaySchedules Skeds ## Point Number Bypass Max setting## Area 1through # ## Relay Number prompt defines ## Relay NumberSelections Blank To 128 for D9412GV3 To 64 for D7412GV3Report ## Defer Test## Hourly Report If Expand Test Report in Phone## Custom Func ## Cmd CenterCmd Center and Custom Func Sound Watch Tone at Command Center Keypad ThisAccess Control Level On This ## Access Ctl Level ### Door 1 through Default Selection To 24, 28 Access Control Level OffAccess Authority Events Unlock Door This functionNo Entry Events Off Default Selection To 24, 28 Access Authority EventsNo Entry Events On D9412GV3/D7412GV3 Program Entry Guide 4.0 Schedules Skeds ## Tuesday ## Time## Date ## MondayHoliday Index # Holiday Indexes## Holiday # DateSDI Automation Enable SDI AutoIntroduction RPS RequirementsStatus Rate SDI RPS ParametersEntered in RPS IP Address Configuration for RPS Over NetworkAnswer RPS Over Network RPS Address VerificationCommand 43, Remote Program Command 43 Flow Chart D1265 RPS Port Number Default Selection 0.0.0.0 toRPS IP Address # Path # Port Number Enhanced CommPath # IP Address  Path # Poll Rate is set to 120 sec Default Selection 0, 5 to 65535 secPath # Poll Rate Example of HeartbeatD1260 Poll Rate Timeline Path # Retry Count SDI RPS/Enhanced Communications ConfigurationDefault Selection 5 sec to 65535 sec Path # Ack WaitRG# Same Network Receiver Route Group ParametersSupervise SDI Fire Supervision Restoral Type Early Ambush TimerFire Summary Sustain Secondary Ambush CodeRemote Warning Crystal Time AdjustPasscode Length Swinger CountEarly Armed Relay Default Disabled Selection Disabled or US CalendarCross Point Parameters Perimeter Relay# Entry Area # Door ProfileCross Point Time Door ## Door Point Default Selection To 127, 129 to 2470 to 75 on D7412GV3#CC#Scope # Custom Function# Fire Unlock? # Interlock Point# Auto Door? # Strike Time Strike Profile# Disarm on Open? # Card Type# RTE Shunt Only? # Buzz Time# Extend Time # Deactivate On Open?# No Entry? # Access Granted?Event Profile # REXShunt Only?# Exit Request? # Enter Request?Programming the Control Panels for SIA CP--01 Compliance SIA CP-01 Quick ReferenceRouting Power SupervisionPhone Phone ParametersKeypad Command Center Assignment50 Area Relays 101 Command 7 and Command 104140 145 143Bosch Security Systems, Inc Perinton Parkway Fairport, NY
Related manuals
Manual 76 pages 25.33 Kb

D9412GV3 specifications

The Bosch Appliances D9412GV3 is a perfect blend of functionality and innovation, designed to meet the needs of modern households. This dishwasher is part of Bosch's reputation for creating high-quality, energy-efficient home appliances. With a sleek design and advanced technology, the D9412GV3 stands out in the crowded market of dishwashers.

One of the main features of the D9412GV3 is its remarkable efficiency. With an Energy Star rating, this model is designed to minimize water and energy consumption while still delivering exceptional cleaning performance. The EcoSense technology optimizes water usage, ensuring every wash cycle is both effective and economical, making it a responsible choice for energy-conscious consumers.

The dishwasher offers a spacious interior, capable of accommodating large loads. Its flexible rack system includes adjustable tines and folding platforms, making it easy to fit various dish sizes, from pots and pans to delicate glassware. Additionally, the third rack feature provides extra space for utensils and smaller items, enhancing its capacity and versatility.

In terms of cleaning power, the D9412GV3 is equipped with the PrecisionWash system. This cutting-edge technology features intelligent sensors that continuously scan and check the load, adjusting the wash cycle as needed for optimal results. Coupled with the 40 dBA noise level, it ensures that the dishwasher operates quietly in the background, so you can enjoy your home without disruptive sounds.

Another standout characteristic is the PureDry technology, an integrated drying system that uses a condensation process to gently dry dishes without the need for extra heat. This not only protects sensitive items but also saves energy, further enhancing the appliance's eco-friendly nature.

Ease of use is a priority for Bosch, as seen in the D9412GV3's user-friendly controls. The intuitive interface allows for selecting various wash cycles and options, including Heavy, Auto, and Quick options, catering to different cleaning needs. Additionally, the Time Delay feature provides the flexibility to set the dishwasher to run at a later time, great for aligning with your schedule.

In summary, the Bosch D9412GV3 combines innovative technologies with a user-centered design to deliver a top-tier dishwasher experience. Its energy-efficient operation, spacious interior, and advanced cleaning features make it an excellent choice for any kitchen, ensuring spotless dishes with minimal effort. With Bosch's commitment to quality, the D9412GV3 stands as a reliable and stylish addition to any modern home.
Top Page Image Contents