Bosch Appliances D9412GV3 manual Area# Account Number, # Force Arm/Bypass Max, Area On to Yes

D9412GV3/D7412GV3 Program Entry Guide 2.0 Panel and Area Wide Parameters

EN 37

Area 1 must be enabled:

 System events such as power and phone supervision do not send a report correctly if Area 1 is disabled.

When programmed No, points assigned to this area do not generate events, show at the keypad when arming and disarming, or send status reports. All user authority in this area is turned off while the area is disabled.

To meet UL 864 requirements, set A#

Area On to Yes.

Area# Account Number

Default: 0000

Selection: For Modem and Contact ID (four- digit account numbers): 0000 to 9999,

BBBB to FFFF

For Modem (ten-digit account numbers): 0000000000 to 9999999999, BBBBBBBBBB to

FFFFFFFFFF

Determines the account number for this area. An account number must be assigned to each active area.

Account numbers are used to group areas together. Each area can have a different account number, or several areas can share the same account number. The control panel uses the account number as a reference for arming and keypad text displays.

Contact ID: Only the last four digits are sent.

Modem IIIa2: Enter a four-digit or ten-digit number.

Keypad Programming of Area # On and Area# Account Number

D1255

1.Refer to Figure 1 on page 7 to access Keypad Programming and navigate to the AREA PARAMETERS option. Press [ENT].

2.The keypad reads AREA NUM 1 – 32 (1 – 8 for the D7412GV3).

3.Enter the area number you wish to configure and press [ENT]. The current area status shows (for example, AREA 1 ON: YES).

4.Press [ENT] to change the area’s status.

5.Press the [PREV] or [NEXT] button to toggle between YES and NO, and then press [ENT] when the desired configuration option shows.

When the keypad reads PARAMETER SAVED, your selection is configured.

6.When the keypad reads AREA STATUS, press [NEXT] to advance to the A# ACCOUNT NUMBER option. The keypad shows the currently configured account number.

7.Press [ENT] to change the account number.

8.The [PREV] button acts as a [Backspace] key. The [COMMAND] key cycles though the special account number characters (B, C, D, E, F); [NEXT] select the account number character. Press [PREV] to delete the characters of the account number and then enter the new account number.

9.Press [ENT] to save the changes.

When the keypad reads Parameter Saved, your selection is configured.

D1260

1.Refer to Figure 2 on page 8 to access Keypad Programming and navigate to the Area Parameters option. Press [ENT].

2.The keypad reads Area Number 1 – 8.

3.Enter the area number you wish to configure and press [Enter]. The current area status shows (for example, Area 1 On: Yes).

4.Press the Edit softkey to change the area’s status.

5.Press the Yes or No softkey, and then press the Save softkey to save the changes.

When the keypad reads Parameter Saved, your selection is configured.

6.When the keypad reads Area Status, press the Account Number softkey. The keypad shows the currently configured account number.

7.Press the Edit softkey to change the account number.

8.Use the softkeys and the number buttons on the keypad to enter the new account number. The Backspace softkey allows you to erase characters. The Clear softkey allows you to clear the entire account number. When entering a letter character, press the letter's softkey to select it. The Previous and Next softkeys advance through the letter characters (A, B, C, D, E, F).

9.Press the Save softkey to save the changes.

When the keypad reads Parameter Saved, your selection is configured.

A# Force Arm/Bypass Max

Default: 1

Selection: 0 to 99

Specify the maximum number of combined Controlled points that can be faulted or bypassed when arming this area.

Bosch Security Systems, Inc. 10/11 F01U170807-02