Logical Solutions SCS-R IP Network, AC Power, 3.1 SCS160 / SCS320 / SCS480, 3.2 SCS160R / SCS320R

Page 18

Product Overview

2.3.2 IP Network

The SCS network interface is an auto-sensing 10 BaseT/100 BaseTX network con- nector (equipped with an RJ45 jack with dual LEDs) for use with a conventional TCP/ IP network using standard RJ45 Category 5 cables. A default IP address is coded into the system (10.9.8.7), however the network settings should be configured by your sys- tem administrator to be suitable for your site’s requirements and unique equipment.

The SCS products are preconfigured for ssh (secure) access.

Note

The SCS-R models offer two independent network interface ports.

Only the first port (NETWORK 1) is enabled by default.

2.3.3 AC Power

2.3.3.1 SCS160 / SCS320 / SCS480

A single IEC-type power entry module is located on the rear of the chassis. The power entry module incorporates a replaceable protective fuse (2A) and an On/Off switch. An IEC cordset is provided with each SCS chassis. Connect the cordset to a local AC power source. Turn the power switch on when appropriate.

2.3.3.2 SCS160R / SCS320R

Two removable AC Power Modules are found on the rear of the chassis, identified as “Left” and “Right” if looking at the rear of the chassis. Either AC module will fully support the system, and if both are turned on, they operate redundantly. The SCS-R systems have an AC Power Monitoring capability to alert the system administrator in the event of an AC Power outage from one of the modules.

Each AC Module has an IEC-type power entry module. The power entry module incorporates a replaceable protective fuse (2A) and an On/Off switch. Two IEC cord- sets are provided with each SCS-R chassis. Connect each cordset to a local AC power source. Turn the power switch on (I) for each module when appropriate.

Caution

During replacement of a module, it is important to first turn the faulty module Off, then remove its power cord, BEFORE youremove the screw to allow the module to be pulled out. The potential for handling hazardous voltages could exist otherwise.

SCS160 / SCS320 / SCS480	Page 18	www.thinklogical.com
SCS160R / SCS320R

Image 18

Contents Product Manual SCS and SCS-R ModelsCopyright Notice Product Overview Initial Configuration Commands Administering Users Regulatory & Safety File System Introduction SCS Models Covered in this ManualSystem Features IntroductionSoftware Features Hardware Features1 SCS160R / SCS320R Hardware SCS480, 48-Port Secure Console Server, front and rear viewsTechnical Specifications TCP/IPSCS320R, showing front and rear views Product Overview Intended ApplicationSystem Chassis 1 SCS160 / SCS320 / SCS4802 SCS160R / SCS320R Connecting to the SCS Serial DevicesBreak Safe 3.1 SCS160 / SCS320 / SCS480 AC PowerIP Network 3.2 SCS160R / SCS320RUser Access Control Port BuffersUser Sessions For Your Notes Installation Mounting the SCSRack Mount or Desktop Front Panel Display and Buttons PowerConnections 3 It’s Convection CooledConnecting to the Network Port Connect your Console3.1 SCS160R / SCS320R Dual NIC Interface Connect to the Ports 4.1 SCS160R / SCS320R Dual Console InterfacePort Adapters Serial Port Pinout PinSCS160R / SCS320R Power Modules Left Supply Failed Tue Mar 18 154307Secure Console Servers SCS160R / SCS320R Power Modules AC Power Module ReplacementReplacing an AC Module Left Module shown partially removed Initial Configuration Default ConfigurationNetwork Connection Requirements Initial System Security ConcernsInitial Connection via Network Route via Linux workstationRoute via Windows workstation From a DOS prompt, enterPuTTY Configuration Screen Front Panel Network Setup Front Panel Edit ModeStart Front Panel Edit Mode SCS Front Panel Display, showing first Edit Mode displayProgram Network Network IP AddressEdit IP Address 192.168.075.239 Net MaskEdit Net Mask 255.200.000.000 GatewayEdit Gateway Exit to Main MenuExit to Main Menu For Your Notes Linux General Public License System AdministrationSCS Systems are Linux-based Understanding LinuxInitial Sysadmin Access Connect using a TerminalSCS System Architecture Enter Commands Log In as rootLog Out Default Services Configure the ServicesConfigure the Services For Your Notes Commands System CommandsSave Command RebootPoweroff Other Linux CommandsSsh-keygen SftpSsh SttyChange Logging Level VersionsFor Your Notes Security Change Network AddressRun netconfig Example of netconfig fill-in fields More Than One NameserverTime Configuration Change HostnameChange NIC Speed Configure Authentications Front Panel Display OptionsDisplay Mode Parameters EditView LINE2 Network Time ServiceLINE1 Display OFFConfigure NTP Start the NTP ServiceChanging Serial Port settings NIS and User Port PermissionsUser Port Control NIS Port Access WhereUser Names and Groups NIS Database fileGroup Permissions NIS Make file NIS Configuration File10 NFS Remote NFS DirectorySnmp SyslogStart Snmp Timeouts Administering Users User SetupEdituser Other Editing CommandsAdduser DeluserEditbrk name Editesc nameFor Your Notes SCS Users User OperationsUser Accounts Root userPort Identities What Can a User DoBreak Sequence Escape SequenceEditbrk Edit Escape Sequence Symbols found on the Product Regulatory & SafetySafety Requirements Product Serial NumberEuropean Union Regulatory ComplianceNorth America Declaration of ConformityStandards With Which the Products Comply Supplementary InformationLithium Battery Australia & New Zealand10.7 SCS160R / SCS320R Power Modules For Your Notes How to Contact Logical Customer SupportWebsite Mail Telephone11.1.4 Fax Product Support WarrantyReturn Authorization Our AddressFor Your Notes Appendix a File System Read-Only vs. Read-WriteLSI Directories Appendix B FAQ How do I do this?View a Buffer Product Support For Your Notes