Agilent Technologies 6050A, 6051A manual Certification

Page 2

CERTIFICATION

Agilent Technologies certifies that this product met its published specifications at time of shipment from the factory. Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Bureau of Standards, to the extent allowed by the Bureau’s calibration facility, and to the calibration facilities of other International Standards Organization members.

WARRANTY

This Agilent Technologies hardware product is warranted against defects in material and workmanship for a period of three years from date of delivery. Agilent Technologies software and firmware products, which are designated by Agilent Technologies for use with a hardware product and when properly installed on that hardware product, are warranted not to fail to execute their programming instructions due to defects in material and workmanship for a period of 90 days from date of delivery. During the warranty period Agilent Technologies will, at its option, either repair or replace products which prove to be defective. Agilent Technologies does not warrant that the operation of the software, firmware, or hardware shall be uninterrupted or error free.

For warranty service, with the exception of warranty options, this product must be returned to a service facility designated by Agilent Technologies Customer shall prepay shipping charges by (and shall pay all duty and taxes) for products returned to Agilent Technologies for warranty service. Except for products returned to Customer from another country, Agilent Technologies shall pay for return of products to Customer.

Warranty services outside the country of initial purchase are included in Agilent Technologies product price, only if Customer pays Agilent Technologies international prices (defined as destination local currency price, or U.S. or Geneva Export price).

If Agilent Technologies is unable, within a reasonable time to repair or replace any product to condition as warranted, the Customer shall be entitled to a refund of the purchase price upon return of the product to Agilent Technologies

LIMITATION OF WARRANTY

The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the Customer, Customer-supplied software or interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper site preparation and maintenance. NO OTHER WARRANTY IS EXPRESSED OR IMPLIED. AGILENT TECHNOLOGIES SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

EXCLUSIVE REMEDIES

THE REMEDIES PROVIDED HEREIN ARE THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES. AGILENT TECHNOLOGIES SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.

ASSISTANCE

The above statements apply only to the standard product warranty. Warranty options, extended support contracts, product maintenance agreements and customer assistance agreements are also available. Contact your nearest Agilent Technologies Sales and Service office for further information on Agilent Technologies’ full line of Support Programs.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Operating Manual Certification Safety Summary Herstellerbescheinigung Safety SummarySymbol Description Manufacturer’s DeclarationPrinting History Page Table of Contents Installation Local OperationCalibration Considerations for Operating in Constant Resistance ModeRemote Operation Page General Information What’s In This ManualOptions Safety Requirements SpecificationsDimensions Page Introduction Operation OverviewRemote Programming Local/Remote ControlFront Panel Description Modes of Operation Extended Power OperationProgrammable Features Triggered Current Level Constant Current CC ModeImmediate Current Level Software Current Limit Constant Resistance CR ModeTransient Current Level Slew RateTriggered Resistance Level Constant Voltage CV ModeImmediate Resistance Level Transient Resistance LevelTransient Operation Triggered Voltage LevelTransient Voltage Level Pulsed Transient Operation Hpsl Command DescriptionContinuous Transient Operation Sets pulse width to 1 millisecond Selects the external trigger inputSelects pulsed transient operation Selects toggled operation Triggering a preset levelSelects the external trigger input source Triggering a transient pulseSlew Rate And Minimum Transition Time Risetime Transition LimitationInput Current, Voltage, and Power Measurement Transition Times and Slew Rates Short On/OffInput On/Off Saving and Recalling SettingsReading Remote Programming Errors Status Reporting Protection FeaturesResetting Latched Protection Overcurrent OverpowerOvervoltage Reverse Voltage Control ConnectorOvertemperature Remote SensingFault External Programming InputPage Installing The Modules InspectionPower Cord Configurations Procedure Installing The Mainframes Channel NumberRack Mounting Turn-On CheckoutCooling Line Voltage Switches Changing Line VoltageTurn-On/Selftest Gpib ErrorsChannel Errors Description Display DescriptionPower Test Controller ConnectionGpib Address Rear Panel Connectors and SwitchesWire Size Strip back AWGInput Binding Post Control Connector Sense SwitchIM and VM Pins Al and A2+Sand -S Com pin A3Application Connections Trigger ConnectorWiring Considerations Local Sense Connections Stranded Copper Wire Ampere Capacity Wire SizeAmpacity Remote Sense ConnectionsMaximum Wire Lengths to Limit Voltage Drops Zero-Volt Loading Connections12. Local Sensing 14. Parallel Operation Page Local Operation Local OperationControls and Indicators Description Chan Keys Function Keys Local Control Overview Using The Chan Keys Identifying the Selected Channel Using The Function KeysSelecting the Channel Turning the Input On/OffRecommended Programming Sequence Programming Ranges Setting the Mode of OperationSetting CC Values ExamplesSetting CR Values Examples Setting CV Values Programming RangeTransient Operation Shorting The Input Displaying Error Codes Using The System KeysSetting The Gpib Address Changing Wake-up Settings Recalling the Factory Default ValuesPage Output Enter/Output StatementsGpib Address EnterGetting Data Back Sending a Remote CommandSelecting a Channel Output 705 MeascurrRemote Programming Commands Output 705INPUT on Output 705MEASCURR? CC Mode ExampleCV Mode Example Output 705 Chan 2INPUT OFF Output 705MODEVOLTRemote Programming Flowchart Sheet Remote Programming Flowchart Sheet Continuous Transient Operation Example CR Mode ExampleOutput 705INPUT on Output 705MEASPOW? Output 705CHAN 2INPUT OFF Output 705MODECURROutput 705CHAN 1INPUT OFF Output 705MODEVOLT Pulsed Transient Operation ExampleSynchronous Toggled Transient Operation Example Output 705 Trigsour TIM Page Equipment Required CalibrationEquipment Required for Calibration Calibration CommandsCharacteristics Recommended ModelCalibration Flowcharts Example ProgramsCalibration Flowchart for a Modules Calibration Flowchart for a Modules Calibration Flowchart for a Modules Pause Subend Program Listing for a ModulesPause Print Voltage Calibration Line ElseEND if 610 Set low calibration point Calibration Flowchart for B Modules Calibration Flowchart for B Modules Calibration Flowchart for B Modules Program Listing for B Modules Clear Screen Print TABXY10,10CALIBRATION DoneWait 1260 If Flag then 1270 Output @LdRESReshipt 1280 Considerations For Operating In Constant Resistance Mode Considerations For Operating In Constant Resistance ModeConsiderations For Operating In Constant Resistance Mode Index IndexIndex Index 19, 20, 21 Agilent Sales and Support Offices Agilent Sales and Support OfficesManual Updates
Top Page Image Contents