Sharp CV-P13LJ To Change Air Flow Direction, Up / Down Air Flow Direction, E-17, mote control

Page 18
TO CHANGE AIR FLOW DIRECTION

TO CHANGE AIR FLOW DIRECTION

UP / DOWN AIR FLOW DIRECTION

 

Press the LOUVERS button on the re-

 

1 mote control.

 

• The horizontal louvers will swing continu-

 

ously.

1

Press the LOUVERS button again when

2 the horizontal louvers are at the desired

2

position.

• The horizontal louvers will stop moving.

• The adjusted position will be memorized and the same position will be set automatically when operated the next time.

NOTE

• During VENTILATION mode, UP/DOWN air fl ow direction cannot be changed.

Horizontal louvers

LEFT / RIGHT AIR FLOW DIRECTION

Hold the vertical louver as shown in the dia- gram and adjust the air fl ow direction.

UP / DOWN AIR FLOW DIRECTION Vertical louvers

CAUTION

Never attempt to adjust the horizontal louvers manually.

Manual adjustment of the horizontal louvers can cause the unit to malfunction when the remote control is used for adjustment.

When the horizontal louvers are positioned at the lowest position in the COOL or DEHUMIDIFI- CATION mode for an extended period of time, condensation may result.

Do not adjust the vertical louvers to the extreme left or right in the COOL mode with the fan speed set to "QUIET (Press the LOUVERS button on the re-)" for an extended period of time.

Condensation may form on the louvers.

E-17

Image 18
Contents CV-P10LJ CV-P13LJ PORTABLE TYPE ROOM AIR CONDITIONEREN GLI SH ES PA ÑO L CONTENTS USAGE CAUTIONS NOTES ON OPERATIONKeep the filter clean PRECAUTIONSLOCATION Turn off the air conditioner when no one is homeSUGGESTED TOOLS FOR WINDOW PANEL INSTALLATION INCLUDED3. Knife or scissors 33 Horizontal louvers 44 POWER Button PART NAMESFRONT VIEW REAR VIEW 55 Remote control signal receiver window1 1 Transmitter 2 Display 3 POWER Button REMOTE CONTROLREMOTE CONTROL DISPLAY 79 ON TIMER ButtonINSTALL WINDOW PANEL Installation in a double-hungsash windowAdjustment panel 24~36.8 Extension panel 36.8~48 Foam seal A adhesive type BracketInstallation in a sliding sash window INSTALL WINDOW PANELE-10 E-11 INSTALLATION AND REMOVAL OF EXHAUST HOSEInstallation of the exhaust hose Unacceptable Acceptable AcceptableRemoval of the exhaust hose E-12PUSH Projection PRE-OPERATIONCHECKS E-13LOADING BATTERIES Use two AAA R03 batteries HOW TO USE THE REMOTE CONTROL E-14E-15 COOL MODEDEHUMIDIFICATION MODE 2 Press the POWER button to start opera- tionTO TURN OFF Press the POWER button again E-16TO TURN OFF Press the POWER button again Press the POWER button to start operationLEFT / RIGHT AIR FLOW DIRECTION TO CHANGE AIR FLOW DIRECTIONUP / DOWN AIR FLOW DIRECTION E-17TO CANCEL PLASMACLUSTER OPERATIONE-18 Press the PLASMACLUSTER button duringE-19 MEGA COOL OPERATIONSLEEP OPERATION TO CANCELOFF TIMER TIMER OPERATIONON TIMER E-20E-21 MAIN UNIT OPERATIONDRAINAGE Press the POWER button on the unitCLEANING THE UNIT AND THE REMOTE CONTROL MAINTENANCECLEANING THE FILTER MAINTENANCE AFTER AIR CONDITIONER SEASONTIMER DOES NOT WORK PROPERLY BEFORE CALLING FOR SERVICEE-23 AIR CONDITIONER DOES NOT OPERATE AT ALLE-24 Technical SpecificationsEvaporator E-25Compressor CondenserE-26 Technical SpecificationsEvaporator E-27Compressor CondenserCongratulations on Your Purchase WARRANTYConsumer Electronic Products DO NOT RETURN THIS DOCUMENT TO SHARPSHARP CUSTOMER SERVICES SHARP APPROVED SERVICE CENTRESHARP APPROVED SERVICE CENTRE 1300Page 66129905937