HP J3177A, J3175A manual Install Any Optional Modules, Installing Modules

Page 12

Installing the Switch 208/224

Installing the Switch 208/224

Installation Steps

2. Install Any Optional Modules

Install optional modules into the Management Slot, Expansion Slot, or trans- ceiver slot by following the instructions in the manuals that accompany these products.

Each of the slot covers can be removed with either a flat-bladed or Torx T-10 screwdriver. Retain the slot covers for future use.

C a u t i o n	To avoid damage to circuitry in the switch and any modules, always unplug
	the power from the switch before installing a module into the Expansion Slot,
	Management Slot, or transceiver slot, and when removing any modules.

If you do not install an optional module, make sure that the cover plate is still attached over the slot for safe operation and proper switch cooling.

Installing Modules

Front of Switch

Management Slot

HP J3178A AdvanceStack Switch 208/224 Management Module

1-4

Image 12

Contents HP AdvanceStack Switch 208/224 Page HP Customer Support Services How to get the latest software/agent firmwareHP FTP Library Service World Wide WebHP First Fax Retrieval Service Additional HP Support ServicesLocation Phone Number HP AdvanceStack Switch 208/224 Installation and Reference GuidePublication Number Contents Index Installing the Switch 208/224 Installing the Switch 208/224Installation Steps Installing the Switch 208/224Included Parts Prepare the Installation Site Installation PrecautionsInstall Any Optional Modules Installing ModulesInstalling Transceivers 100Base-T transceiver modules into the Switch 208/224Do not install any 100VG transceiver modules in this slot Verify the Switch’s Operation When the self test completes successfully LED BehaviorMount the Switch Mounting the Switch in a Rack or CabinetInsert a screw into the top hole of a close 0.5-inch Install additional screw Mounting the Switch on a Wall Mounting the Switch on a Horizontal SurfaceConnect the Switch to a Power Source Using RJ-45 Connectors 10 Mbit/s and 100 Mbit/s ports Connect the Network Cables100Base-T Xcvr Slot To connectSwitch 208/224 Condition Diagnostic Tip InstallingAs a Segment Switch Switch 208TSample Network Topologies As a Desktop Switch Switch 224T PCs and peripheralsServer Connecting to a Backbone Switch Fddi Campus Backbone Installing the Switch 208/224Switch Switch 224T Switch 208TWhere to Go From Here Cable ManagementSwitch 208/224 Description FeaturesFront of the Switches Switch 208/224 DescriptionNetwork Ports LEDs State MeaningManagement Module Features Management SlotBack of the Switches Power ConnectorsRedundant Power Supply RPS Connector Expansion SlotSwitch Operation Address Table OperationSimultaneous Network Communications Page Troubleshooting Solutions to Common ProblemsTroubleshooting Wrong network speed connected -- You have connected aLED Error Indications Diagnostic TipsDiagnostic Tests Testing the SwitchTesting Twisted-Pair Cabling Testing End-to-End Network Communications Testing Switch-to-Device Network CommunicationsResetting the Switch HP BBSCables and Connectors Twisted-Pair Cable/Connector Pin-OutsCables and Connectors White/orange Fiber-Optic Cables Twisted-Pair Cable Pin AssignmentsTwisted-Pair Straight-Through Cable Twisted-Pair Cross-Over CableSpecifications PhysicalElectrical EnvironmentalConnectors SafetySpecifications ElectromagneticSafety and Regulatory Statements Mounting PrecautionsPower Precautions Safety and Regulatory StatementsSafety Information GroundingServicing Informations concernant la sécurité Tible de causer des dommages à léquipementHinweise zur Sicherheit Considerazioni sulla sicurezza AttrezzatureConsideraciones sobre seguridad Resultar en averías al equipoSafety Information Japanese Regulatory Statements FCC Class a Statement for U.S.A. OnlyEuropean Community CanadaDeclaration of Conformity Index NumericsMounting switch on … 1-11 HP Redundant Power Supply RPS Rack Page Page 5966-5225