|
|
|
|
| Switch 208/224 Description |
|
|
|
|
| Front of the Switches |
|
|
| LEDs |
| |
|
|
|
|
|
|
LED | State |
| Meaning | ||
|
|
|
|
|
|
Power (green) | Off |
| The switch is not receiving power. | ||
|
|
|
|
|
|
|
|
| On |
| The switch is receiving power. |
|
|
|
|
|
|
Fault | On |
| The switch has failed its | ||
|
|
|
|
|
|
|
|
| Flashing |
| An incorrect transceiver has been installed in the transceiver slot, or a connected |
|
|
| Slowly* |
| RPS has a failure. The corresponding LED (transceiver port or RPS) will also flash. |
|
|
|
|
|
|
|
|
| Off |
| The normal state. Indicates that there are no fault conditions on the switch. |
|
|
|
|
|
|
RPS | Off |
| This switch is not receiving power from the HP J2962A Redundant Power Supply | ||
|
|
|
|
| (RPS). |
|
|
|
|
|
|
|
|
| On |
| This switch is receiving power from the connected RPS. |
|
|
|
|
|
|
|
|
| Flashing |
| An error has occurred on the RPS connected to the switch. See the documentation |
|
|
| Slowly* |
| provided with the RPS for troubleshooting. |
|
|
|
|
|
|
Expansion Slot |
|
| The behavior of these four LEDs depends on the module inserted into the Expansion | ||
Module LEDs (4) |
|
| Slot. See the module manual for a description of these LEDs. | ||
|
|
|
|
|
|
|
|
| On |
| Indicates that an optional module is installed in the expansion slot in the back of the |
|
|
|
|
| switch. Any expansion modules installed into the switch use the port 1 circuitry to |
|
|
|
|
| |
(port 1 disabled) |
|
| communicate with the network through the switch. Therefore, when a module is | ||
|
|
|
|
| installed, the port 1 |
|
|
|
|
|
|
|
|
| Off |
| The port 1 |
|
|
|
|
| to the switch. |
|
|
|
|
|
|
100 Mbit/s Ports |
|
|
| ||
|
|
|
|
|
|
A or B | Off |
| No active network cable is connected to the port. For port B, could indicate that | ||
|
|
|
|
| there is no transceiver installed. Could also indicate that the port has been disabled |
|
|
|
|
| through the switch console or HP AdvanceStack Assistant (port configuration |
|
|
|
|
| changes require a Switch Management Module to be installed). |
|
|
|
|
|
|
|
|
| On |
| During the first 3 seconds after an active network cable is connected or after a |
|
|
|
|
| switch reset, indicates the port is enabled and receiving a link beat signal . After 3 |
|
|
|
|
| seconds, On continuously indicates a saturated network segment on the port. |
|
|
|
|
|
|
|
|
| Flickering |
| Indicates activity on the port. |
|
|
|
|
|
|
|
|
| Flashing |
| This condition will only occur on the 100 Mbit/s port B (the transceiver port), if an |
|
|
| Slowly* |
| incorrect transceiver is installed in the slot. |
|
|
|
|
|
|
100 |
|
| On |
| The port is operating in 100 Mbit/s mode. |
|
|
|
|
|
|
Fdx | On |
| The port is operating in | ||
|
|
|
|
|
|
|
|
| Off |
| The port is operating is |
|
|
|
|
|
|
Switch 208/224 Description