HP J3175A, J3177A manual Insert a screw into the top hole of a close 0.5-inch

Page 17

Installing the Switch 208/224

Installation Steps

2.Partially install a screw (5/8-inch number 12-24) into the top hole of a pair of holes that are 0.5 inches apart in each rack/cabinet upright as shown in the illustration below. Tighten each screw enough to support the weight of the switch, approximately two turns. Ensure that the screws are at the same level in each upright.

Insert a screw into the top hole of a close (0.5-inch)

3.Place the switch in the rack and lower it so the notches in the bottom of the bracket slide onto the screws. Tighten these screws-be careful not to overtighten.

Installing the Switch 208/224

1-9

Image 17

Contents HP AdvanceStack Switch 208/224 Page How to get the latest software/agent firmware HP Customer Support ServicesHP FTP Library Service World Wide WebLocation Phone Number HP First Fax Retrieval ServiceAdditional HP Support Services Installation and Reference Guide HP AdvanceStack Switch 208/224Publication Number Contents Index Installing the Switch 208/224 Installing the Switch 208/224Included Parts Installation StepsInstalling the Switch 208/224 Installation Precautions Prepare the Installation SiteInstalling Modules Install Any Optional ModulesDo not install any 100VG transceiver modules in this slot Installing Transceivers100Base-T transceiver modules into the Switch 208/224 Verify the Switch’s Operation LED Behavior When the self test completes successfullyMounting the Switch in a Rack or Cabinet Mount the SwitchInsert a screw into the top hole of a close 0.5-inch Install additional screw Mounting the Switch on a Horizontal Surface Mounting the Switch on a WallConnect the Switch to a Power Source Connect the Network Cables Using RJ-45 Connectors 10 Mbit/s and 100 Mbit/s ports100Base-T Xcvr Slot To connectCondition Diagnostic Tip Installing Switch 208/224Sample Network Topologies As a Segment SwitchSwitch 208T Server As a Desktop SwitchSwitch 224T PCs and peripherals Fddi Campus Backbone Installing the Switch 208/224 Connecting to a Backbone SwitchSwitch Switch 224T Switch 208TCable Management Where to Go From HereFeatures Switch 208/224 DescriptionNetwork Ports Front of the SwitchesSwitch 208/224 Description State Meaning LEDsManagement Slot Management Module FeaturesPower Connectors Back of the SwitchesRedundant Power Supply RPS Connector Expansion SlotAddress Table Operation Switch OperationSimultaneous Network Communications Page Solutions to Common Problems TroubleshootingWrong network speed connected -- You have connected a TroubleshootingDiagnostic Tips LED Error IndicationsTesting Twisted-Pair Cabling Diagnostic TestsTesting the Switch Testing Switch-to-Device Network Communications Testing End-to-End Network CommunicationsHP BBS Resetting the SwitchTwisted-Pair Cable/Connector Pin-Outs Cables and ConnectorsCables and Connectors White/orange Twisted-Pair Cable Pin Assignments Fiber-Optic CablesTwisted-Pair Straight-Through Cable Twisted-Pair Cross-Over CablePhysical SpecificationsElectrical EnvironmentalSafety ConnectorsSpecifications ElectromagneticMounting Precautions Safety and Regulatory StatementsSafety and Regulatory Statements Power PrecautionsServicing Safety InformationGrounding Tible de causer des dommages à léquipement Informations concernant la sécuritéHinweise zur Sicherheit Attrezzature Considerazioni sulla sicurezzaResultar en averías al equipo Consideraciones sobre seguridadSafety Information Japanese FCC Class a Statement for U.S.A. Only Regulatory StatementsEuropean Community CanadaDeclaration of Conformity Numerics IndexMounting switch on … 1-11 HP Redundant Power Supply RPS Rack Page Page 5966-5225