HP J3177A, J3175A manual Connect the Switch to a Power Source

Page 20

Installing the Switch 208/224

Installing the Switch 208/224

Installation Steps

5. Connect the Switch to a Power Source

1.(Optional.) This product supports use of the HP J2962A Redundant Power Supply (RPS), which can help ensure continuous switch operation in the event of a power failure. If you have this HP RPS, connect the RPS to the switch now and connect the RPS to an appropriate AC power source.

C a u t i o n

When installed, the RPS is used in place of the standard power cord, so make

 

sure you disconnect the standard power cord from the switch before you

 

connect the RPS. Using both the standard power cord and the RPS at the same

 

time could damage the switch’s components.

 

 

Back of Switch

Back of RPS

For information on how to install and connect the HP RPS, refer to the documentation supplied with the RPS.

2.If you are not using an RPS, plug the included power cord into the switch's power cord receptacle and into an AC power source as shown below.

power receptacle

on the back of the switch

3.Re-check the LEDs during self test. Initially, all LEDs are on. After the four-second self test (or 15 second self test with Management Module), only the Power and port A “100” LEDs (and optionally the RPS LED) are on. See “LED Behavior” on page 7.

1-12

Image 20
Contents HP AdvanceStack Switch 208/224 Page HP Customer Support Services How to get the latest software/agent firmwareHP FTP Library Service World Wide WebLocation Phone Number HP First Fax Retrieval ServiceAdditional HP Support Services HP AdvanceStack Switch 208/224 Installation and Reference GuidePublication Number Contents Index Installing the Switch 208/224 Installing the Switch 208/224Included Parts Installation StepsInstalling the Switch 208/224 Prepare the Installation Site Installation PrecautionsInstall Any Optional Modules Installing ModulesDo not install any 100VG transceiver modules in this slot Installing Transceivers100Base-T transceiver modules into the Switch 208/224 Verify the Switch’s Operation When the self test completes successfully LED BehaviorMount the Switch Mounting the Switch in a Rack or CabinetInsert a screw into the top hole of a close 0.5-inch Install additional screw Mounting the Switch on a Wall Mounting the Switch on a Horizontal SurfaceConnect the Switch to a Power Source Using RJ-45 Connectors 10 Mbit/s and 100 Mbit/s ports Connect the Network Cables100Base-T Xcvr Slot To connectSwitch 208/224 Condition Diagnostic Tip InstallingSample Network Topologies As a Segment SwitchSwitch 208T Server As a Desktop SwitchSwitch 224T PCs and peripherals Connecting to a Backbone Switch Fddi Campus Backbone Installing the Switch 208/224Switch Switch 224T Switch 208TWhere to Go From Here Cable ManagementSwitch 208/224 Description FeaturesNetwork Ports Front of the SwitchesSwitch 208/224 Description LEDs State MeaningManagement Module Features Management SlotBack of the Switches Power ConnectorsRedundant Power Supply RPS Connector Expansion SlotSwitch Operation Address Table OperationSimultaneous Network Communications Page Troubleshooting Solutions to Common ProblemsTroubleshooting Wrong network speed connected -- You have connected aLED Error Indications Diagnostic TipsTesting Twisted-Pair Cabling Diagnostic TestsTesting the Switch Testing End-to-End Network Communications Testing Switch-to-Device Network CommunicationsResetting the Switch HP BBSCables and Connectors Twisted-Pair Cable/Connector Pin-OutsCables and Connectors White/orange Fiber-Optic Cables Twisted-Pair Cable Pin AssignmentsTwisted-Pair Straight-Through Cable Twisted-Pair Cross-Over CableSpecifications PhysicalElectrical EnvironmentalConnectors SafetySpecifications ElectromagneticSafety and Regulatory Statements Mounting PrecautionsPower Precautions Safety and Regulatory StatementsServicing Safety InformationGrounding Informations concernant la sécurité Tible de causer des dommages à léquipementHinweise zur Sicherheit Considerazioni sulla sicurezza AttrezzatureConsideraciones sobre seguridad Resultar en averías al equipoSafety Information Japanese Regulatory Statements FCC Class a Statement for U.S.A. OnlyEuropean Community CanadaDeclaration of Conformity Index NumericsMounting switch on … 1-11 HP Redundant Power Supply RPS Rack Page Page 5966-5225