HP J3175A manual Connect the Network Cables, Using RJ-45 Connectors 10 Mbit/s and 100 Mbit/s ports

Page 21

Installing the Switch 208/224

Installation Steps

6. Connect the Network Cables

Using RJ-45 Connectors (10 Mbit/s and 100 Mbit/s ports)

To connect:

Push the RJ-45 plug into the RJ-45 jack until the tab on the plug clicks into place.

When power is on for the switch and the connected device, the Port LED should light to confirm a powered-on device

(for example, an end node) is at the other end of the cable.

RJ-45 plug

Installing the Switch 208/224

To disconnect:

Press the small tab on the plug and pull the plug out of the jack.

Caution:

Do not connect a 10 Mbit/s network into either of the 100 Mbit/s ports.

Unshielded twisted-pair cable: Category 3, 4, or 5 for 10 Mbit/s ports Category 5 only for 100 Mbit/s ports

Cat 3, 4 maximum distance: 100 meters

Cat 5 maximum distance: 150 meters for 10BT 100 meters for 100BT

100Base-T Xcvr Slot

An optional 100Base-T transceiver module can be installed in the switch’s transceiver (Xcvr) slot to provide additional connectivity choices, including:

HP 100Base-FX Fiber-Optic Transceiver Module (HP J3193B)

Maximum Distance: 1 kilometer

HP 100Base-TX Twisted-Pair Transceiver Module (HP J3192B)

Category 5 maximum distance: 100 meters

See the documentation accompanying the optional transceiver modules for cabling configurations for those modules.

1-13

Image 21
Contents HP AdvanceStack Switch 208/224 Page How to get the latest software/agent firmware HP Customer Support ServicesHP FTP Library Service World Wide WebHP First Fax Retrieval Service Additional HP Support ServicesLocation Phone Number Installation and Reference Guide HP AdvanceStack Switch 208/224Publication Number Contents Index Installing the Switch 208/224 Installing the Switch 208/224Installation Steps Installing the Switch 208/224Included Parts Installation Precautions Prepare the Installation SiteInstalling Modules Install Any Optional ModulesInstalling Transceivers 100Base-T transceiver modules into the Switch 208/224Do not install any 100VG transceiver modules in this slot Verify the Switch’s Operation LED Behavior When the self test completes successfullyMounting the Switch in a Rack or Cabinet Mount the SwitchInsert a screw into the top hole of a close 0.5-inch Install additional screw Mounting the Switch on a Horizontal Surface Mounting the Switch on a WallConnect the Switch to a Power Source Connect the Network Cables Using RJ-45 Connectors 10 Mbit/s and 100 Mbit/s ports100Base-T Xcvr Slot To connectCondition Diagnostic Tip Installing Switch 208/224As a Segment Switch Switch 208TSample Network Topologies As a Desktop Switch Switch 224T PCs and peripheralsServer Fddi Campus Backbone Installing the Switch 208/224 Connecting to a Backbone SwitchSwitch Switch 224T Switch 208TCable Management Where to Go From HereFeatures Switch 208/224 DescriptionFront of the Switches Switch 208/224 DescriptionNetwork Ports State Meaning LEDsManagement Slot Management Module FeaturesPower Connectors Back of the SwitchesRedundant Power Supply RPS Connector Expansion SlotAddress Table Operation Switch OperationSimultaneous Network Communications Page Solutions to Common Problems TroubleshootingWrong network speed connected -- You have connected a TroubleshootingDiagnostic Tips LED Error IndicationsDiagnostic Tests Testing the SwitchTesting Twisted-Pair Cabling Testing Switch-to-Device Network Communications Testing End-to-End Network CommunicationsHP BBS Resetting the SwitchTwisted-Pair Cable/Connector Pin-Outs Cables and ConnectorsCables and Connectors White/orange Twisted-Pair Cable Pin Assignments Fiber-Optic CablesTwisted-Pair Straight-Through Cable Twisted-Pair Cross-Over CablePhysical SpecificationsElectrical EnvironmentalSafety ConnectorsSpecifications ElectromagneticMounting Precautions Safety and Regulatory StatementsSafety and Regulatory Statements Power PrecautionsSafety Information GroundingServicing Tible de causer des dommages à léquipement Informations concernant la sécuritéHinweise zur Sicherheit Attrezzature Considerazioni sulla sicurezzaResultar en averías al equipo Consideraciones sobre seguridadSafety Information Japanese FCC Class a Statement for U.S.A. Only Regulatory StatementsEuropean Community CanadaDeclaration of Conformity Numerics IndexMounting switch on … 1-11 HP Redundant Power Supply RPS Rack Page Page 5966-5225