HP Ethernet BL-c manual Runtime switching software default settings, General default settings

Page 33

Port type	Port number	Port name	STP

Server	4	Downlink4	Disabled

Server	5	Downlink5	Disabled

Server	6	Downlink6	Disabled

Server	7	Downlink7	Disabled

Server	8	Downlink8	Disabled

Server	9	Downlink9	Disabled

Server	10	Downlink10	Disabled

Server	11	Downlink11	Disabled

Server	12	Downlink12	Disabled

Server	13	Downlink13	Disabled

Server	14	Downlink14	Disabled

Server	15	Downlink15	Disabled

Server	16	Downlink16	Disabled

X-Connect	17	XConnect1	Enabled

Mgmt	18	Mgmt	Enabled

Uplink	19	Uplink1	Enabled

Uplink	20	Uplink2	Enabled

Uplink	21	Uplink3	Enabled

Uplink	22	Uplink4	Enabled

Uplink	23	Uplink5	Enabled

Uplink	24	Uplink6	Enabled

Uplink	25	Uplink7	Enabled

Runtime switching software default settings

General default settings

Setting	Value

Notice	None

Banner	None

User names and	User names and passwords:
passwords	• user—Enabled, password is user
	• user—Enabled, password is user
	• oper—Disabled, no password
	• admin—Enabled (cannot be disabled), password is admin

BOOTP service	Enabled

IP address (if manual IP	0.0.0.0
option is selected)

Subnet mask (if manual IP	0.0.0.0
option is selected)

	Technical specifications 33

Image 33

Contents HP 110Gb Ethernet BL-c Switch User Guide Audience assumptions Contents Replacing a switch Acronyms and abbreviations Index Introduction FeaturesAdditional references Enterprise class performanceIntroduction Configuration and management Switch redundancySwitch architecture Diagnostic toolsPort Mapping Dual switches Layer 3 switching Layer 2 switchingSupported technologies Redundant crosslinksSpanning Tree Protocol Ieee 802.1 Q-based VlanPort mirroring Store and forward switching schemePort trunking and load balancing Tftp supportRadius XModem SSH and SCPIgmp Snooping Jumbo framesRedundant images in firmware Component identification 110Gb Ethernet Blade Switch front panelGreen-Link LED top Preparing for installation Installing the switchPlanning the switch configuration Default settingsUser, operator, and administrator access rights Switch securityConfiguring multiple switches Manually configuring a switchInstalling the switch Accessing the switch Logging on and configuring the switch Supporting software and special considerations Installing XFP transceiversInstalling the switch Replacing an existing switch Replacing a switchReplacing a switch Class a equipment Regulatory compliance noticesModifications CablesBsmi notice Japanese class a notice European Union regulatory noticeKorean class a notice Laser compliance General specifications Technical specificationsSTP Port names, VLANs, STP, trunking default settingsGeneral default settings Runtime switching software default settingsSTP Algorithm Setting Value Mstp UFD Igmp Performance specifications Physical and environmental specificationsCategory Specification Serial upgrade of boot code firmware image procedure Performing a serial downloadIntroduction Performing a serial download Performing a serial download 10G100.bin Serial upgrade of operating system firmware procedurePerforming a serial download Performing a serial download Snmp MIBs support MIB overviewSnmp Manager software Supported traps Supported MIBsSnmp MIBs support Electrostatic discharge Preventing electrostatic dischargeGrounding methods to prevent electrostatic discharge Standard RJ-45 receptacle/connector RJ-45 pin specificationRJ-45 signals RJ-45 pins DB-9 pins DB-9 signals Health LED on the switch is not on TroubleshootingTroubleshooting Bootp Page Troubleshooting Troubleshooting Switch configuration is corrupt XFP transceiver port is disabledDownload fails after starting to download the firmware file Acronyms and abbreviations Ieee NTP SCP Index Switch self-test, troubleshooting