HP Ethernet BL-c manual Algorithm

Page 35

Setting

Value

 

 

Port Trunking Load Sharing

The algorithm selects the following as forwarding ports for forwarding traffic:

Algorithm

1 For forwarding IP Packets—modulus of XOR of last 3 bits of source and last 3

 

 

bits of Destination IP address

 

2 For forwarding non-IP packets—modulus of XOR of last 3 bits of source and

 

last 3 bits of Destination MAC address

 

3 For forwarding broadcast, multicast packets, and unknown unicast packets—

 

the lowest active port number in the trunk group

 

 

Port Mirroring-Mirror Status

Disabled

 

 

Port Mirroring-Mirror Port

None selected

 

 

Port Mirroring-Mirror Port

None selected

Traffic Direction

 

 

 

Port Mirroring-Monitoring

None selected

Port

 

 

 

SNMP

Read/write

 

 

SNMP System Name

None

 

 

SNMP System Location

None

 

 

SNMP System Contact

None

 

 

SNMP Community

Public—read-only

String/Access Right

Private—read/write

 

 

 

SNMP Trap Host 1

0.0.0.0

 

 

SNMP Trap Host 1

Public

Community String

 

 

 

SNMP Trap Host 2

0.0.0.0

 

 

SNMP Trap Host 2

Public

Community String

 

 

 

SNMP Authentication

Disabled

Traps

 

 

 

SNMP Link Up/Down

Enabled

Traps

 

 

 

Security IP Network/Mask

0.0.0.0 / 0.0.0.0

 

 

TFTP Server IP Address

0.0.0.0

 

 

TFTP Port Number

69

 

 

Firmware upgrade

File name—none

 

 

Configuration file from

File name—none

TFTP server

 

 

 

Configuration file to TFTP

File name—none

server

 

 

 

PING tool

Target address—undefined

 

Default tries—5

 

 

Trace Route tools

Target address—undefined

 

 

Serial Port Baud Rate

9600

 

 

Serial Port Data Bit

8

 

 

Technical specifications 35

Image 35
Contents HP 110Gb Ethernet BL-c Switch User Guide Audience assumptions Contents Replacing a switch Acronyms and abbreviations Index Enterprise class performance FeaturesIntroduction Additional referencesIntroduction Configuration and management Switch redundancyPort Mapping Dual switches Switch architectureDiagnostic tools Redundant crosslinks Layer 2 switchingLayer 3 switching Supported technologiesSpanning Tree Protocol Ieee 802.1 Q-based VlanTftp support Store and forward switching schemePort mirroring Port trunking and load balancingRadius Jumbo frames SSH and SCPXModem Igmp SnoopingRedundant images in firmware Component identification 110Gb Ethernet Blade Switch front panelGreen-Link LED top Default settings Installing the switchPreparing for installation Planning the switch configurationUser, operator, and administrator access rights Switch securityConfiguring multiple switches Manually configuring a switchInstalling the switch Accessing the switch Logging on and configuring the switch Supporting software and special considerations Installing XFP transceiversInstalling the switch Replacing an existing switch Replacing a switchReplacing a switch Cables Regulatory compliance noticesClass a equipment ModificationsBsmi notice Japanese class a notice European Union regulatory noticeKorean class a notice Laser compliance General specifications Technical specificationsSTP Port names, VLANs, STP, trunking default settingsGeneral default settings Runtime switching software default settingsSTP Algorithm Setting Value Mstp UFD Igmp Performance specifications Physical and environmental specificationsCategory Specification Introduction Serial upgrade of boot code firmware image procedurePerforming a serial download Performing a serial download Performing a serial download 10G100.bin Serial upgrade of operating system firmware procedurePerforming a serial download Performing a serial download Snmp Manager software Snmp MIBs supportMIB overview Supported traps Supported MIBsSnmp MIBs support Grounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Standard RJ-45 receptacle/connector RJ-45 pin specificationRJ-45 signals RJ-45 pins DB-9 pins DB-9 signals Health LED on the switch is not on TroubleshootingTroubleshooting Bootp Page Troubleshooting Troubleshooting Download fails after starting to download the firmware file Switch configuration is corruptXFP transceiver port is disabled Acronyms and abbreviations Ieee NTP SCP Index Switch self-test, troubleshooting