HP 400N manual Components face right for CopyJet CopyJet M printers

Page 44

To install the card into the HP CopyJet and CopyJet M color printer-copiers

1.Turn off the printer and unplug the power cord.

2.Locate the HP modular I/O (MIO) slot at the back of the printer (see the figure below).

Components face right for CopyJet and

CopyJet M printers

3.If the slot has a cover plate, remove it.

4.Insert the card. Align the card with the guide rails in the printer.

5.Press the card into the slot until the card is firmly seated.

6.Tighten each thumbscrew a little at a time, alternating between each side until both of the screws are secure.

7.Connect the network cable to the card.

8.Connect the power cord and turn on the printer.

NOTE

For the HP J4100A JetDirect card (RJ-45 and

 

BNC), you can connect to one of the Ethernet ports

 

(only one Ethernet port is active at a time).

 

For the HP J4105A JetDirect card (RJ-45 and DB9),

 

you can connect to only one Token Ring port.

 

 

2-30 Installing the HP JetDirect Print Server Card

Image 44
Contents HP JetDirect 400N Page Hardware Installation Guide HP JetDirect 400N Print Server Safety Symbols HP JetDirect Print Servers HP J4105A HP J4106AQuick Installation If you have a Token Ring cardVerify that the card was installed correctly Quick Installation Contents Specifications and Regulatory Statements HP J4100A 10/100Base-TX Print ServerHP JetDirect Print Server Card Introduction HP JetDirect Print Server Cards at a Glance Network Types Connections SupportedSupported Networks LPDWhat You Need for Installation Installation Task 2. Before installing the card, verify the printer works HP LaserJet 5, 5M, and 5N printersHP LaserJet 5Si, 5Si MX, 5Si NX, 5Si Mopier printers HP Color LaserJet and Color LaserJet 5, 5M printers Press Enter. a self-test page will printHP LaserJet 4, 4M, 4 Plus, and 4M Plus printers HP LaserJet 4Si and 4Si MX printers HP LaserJet 4V and 4MV printers Ready HP DeskJet 1600C, 1600CM, and 1600CN printers HP DeskJet 1200C and 1200 C/PS printersHP DesignJet 600 Series large-format printers UtilitiesInstallation HP CopyJet and CopyJet M color printer-copiers Press -to print the TestComponents face right for 4, 4M, 4 Plus, or 4M Plus Components face left for Color LaserJets including 5/5M To install the card into the HP LaserJet 4V and 4MV printers Components face right for HP LaserJet 5, 5M, 5N Installation Installing the HP JetDirect Print Server Card Installation To use the upper slot of an HP LaserJet 4Si or 4Si Remove faceplate from card Peel off label parts and attach cover plate to card Connect cards with customized plate at right Insertion of two cards into HP LaserJet 4Si/4SiMX For the HP J4100A JetDirect card RJ-45 Connect the power cord Turn on the power switch Installation Turn off the printer but leave the power cord plugged Installation Components face right for CopyJet CopyJet M printers Task 4. Verify the card was installed correctly Location of I/O Card Ready message on self-test pages What To Do Next Installing the HP JetDirect Print Server Card Printer Control Panel To restore configuration default values Enabling and Disabling Network ProtocolsTo enable or disable network protocols Proceed to StepConfiguring Novell NetWare Frame Types Novell NetWare Frame Types On an HP JetDirect Ethernet CardTo configure a NetWare frame type TrsnapUsing the Control Panel for Printers To configure NetWare source routing Press Item until SRC RT=Source Routing* appears Configuring TCP/IP Parameters To configure TCP/IP parameters Shift keys To configure EtherTalk parameters Printer Control Panel Configuring the Timeout for End-of-Job Sensing Select To configure a NetWare frame type Configuring TCP/IP Parameters Using the Control Panel for Printers To configure EtherTalk parameters Using the Control Panel for Printers HP DesignJet 4 Control Panel Supported Network Protocols Press Enter. MIO Setup and CFG NETWORK=NO→ appear You will see CFG NETWORK=NO whenever you enter Press ↓ to change NO* to YES, then press Enter to display Detected For the 600 Series Printers MIO Setup and CFG IPX/SPX=YES→ appear Configuring TCP/IP Parameters If a printer is configured through DHCP, IP Byte 1=new value→ appear Control Panel for Large-Format Printers EtherTalk is supported by HP DesignJet 650C To set the JOB Timeout parameter Current value→ appear Control Panel for Large-Format Printers Electrical Regulatory Statements FCC StatementsEuropean Community Declaration of Conformity Japan Vcci Class a RRL Statement Korea Taiwan Class a AustraliaCanada Chinese Safety Statement HP J4100A 10/100Base-TX Print Server Supported Links Link-Speed LEDsLink Configuration Jumper Settings Link Configuration jumpersLink Troubleshooting HP J4100A 10/100Base-TX Print Server Page 5969-3587