HP 400N manual IP Byte 1=new value→ appear

Page 79

5.Press ↑ to configure each TCP/IP parameter. For the first parameter, MIO SETUP and IP BYTE 1=<value>→ appear.

6.To maintain the current value, press ↑.

7.To change the value, proceed as follows:

a.Press [Enter] to display the current value.

b.Press ↑ until the value that you want appears.

c.Press [Enter] to save the new value. MIO SETUP and

IP BYTE 1=<new value>→ appear.

d.Press ↑ to continue.

8.Configure the remaining bytes of the IP address in the same manner. Note that a valid IP address is required for proper operation.

9.If you want, configure the subnet mask bytes (SM), syslog server IP address (LG), default gateway (GW), and timeout (TIMEOUT) in the same manner.

The TIMEOUT parameter default is 90 seconds. Up to 3600 seconds can be configured. If set to “0”, the timeout feature of the HP JetDirect card is disabled—TCP/IP connections remain open until closed by the server.

10.Press [Previous] until Ready to plot is displayed.

For the 700/2000/2500/3000/3500 Series Printers

1.Access the configuration menu (see “To enable or disable network protocols” in this chapter).

2.From the CFG TCP/IP=NO→ menu item, press [Enter], ↓, [Enter] to display CFG TCP/IP=YES→ .

3.Press ↑ to display “BOOTP=”.

a.To maintain the current “BOOTP=” setting, press ↑ .

b.To change the “BOOTP=” setting, press [Enter], ↑ , [Enter].

•If you select BOOTP=YES→ , the printer is configured to retrieve its TCP/IP parameters over the network using BOOTP or DHCP.

No other TCP/IP prompts are displayed on the printer's control panel. Press ↑ to continue with configuration of other network protocols, or press [Previous] until the STATUS Ready is displayed.

HP DesignJet 4 Control Panel

Control Panel for Large-Format Printers 4-11

Image 79

Contents HP JetDirect 400N Page Hardware Installation Guide HP JetDirect 400N Print Server Safety Symbols HP J4105A HP J4106A HP JetDirect Print ServersIf you have a Token Ring card Quick InstallationVerify that the card was installed correctly Quick Installation Contents HP J4100A 10/100Base-TX Print Server Specifications and Regulatory StatementsHP JetDirect Print Server Card Introduction Network Types Connections Supported HP JetDirect Print Server Cards at a GlanceLPD Supported NetworksWhat You Need for Installation Installation HP LaserJet 5, 5M, and 5N printers Task 2. Before installing the card, verify the printer worksHP LaserJet 5Si, 5Si MX, 5Si NX, 5Si Mopier printers Press Enter. a self-test page will print HP Color LaserJet and Color LaserJet 5, 5M printersHP LaserJet 4, 4M, 4 Plus, and 4M Plus printers HP LaserJet 4Si and 4Si MX printers HP LaserJet 4V and 4MV printers Ready HP DeskJet 1200C and 1200 C/PS printers HP DeskJet 1600C, 1600CM, and 1600CN printersUtilities HP DesignJet 600 Series large-format printersInstallation Press -to print the Test HP CopyJet and CopyJet M color printer-copiersComponents face right for 4, 4M, 4 Plus, or 4M Plus Components face left for Color LaserJets including 5/5M To install the card into the HP LaserJet 4V and 4MV printers Components face right for HP LaserJet 5, 5M, 5N Installation Installing the HP JetDirect Print Server Card Installation To use the upper slot of an HP LaserJet 4Si or 4Si Remove faceplate from card Peel off label parts and attach cover plate to card Connect cards with customized plate at right Insertion of two cards into HP LaserJet 4Si/4SiMX For the HP J4100A JetDirect card RJ-45 Connect the power cord Turn on the power switch Installation Turn off the printer but leave the power cord plugged Installation Components face right for CopyJet CopyJet M printers Task 4. Verify the card was installed correctly Location of I/O Card Ready message on self-test pages What To Do Next Installing the HP JetDirect Print Server Card Printer Control Panel Enabling and Disabling Network Protocols To restore configuration default valuesProceed to Step To enable or disable network protocolsNovell NetWare Frame Types On an HP JetDirect Ethernet Card Configuring Novell NetWare Frame TypesTrsnap To configure a NetWare frame typeUsing the Control Panel for Printers To configure NetWare source routing Press Item until SRC RT=Source Routing* appears Configuring TCP/IP Parameters To configure TCP/IP parameters Shift keys To configure EtherTalk parameters Printer Control Panel Configuring the Timeout for End-of-Job Sensing Select To configure a NetWare frame type Configuring TCP/IP Parameters Using the Control Panel for Printers To configure EtherTalk parameters Using the Control Panel for Printers HP DesignJet 4 Control Panel Supported Network Protocols Press Enter. MIO Setup and CFG NETWORK=NO→ appear You will see CFG NETWORK=NO whenever you enter Press ↓ to change NO* to YES, then press Enter to display Detected For the 600 Series Printers MIO Setup and CFG IPX/SPX=YES→ appear Configuring TCP/IP Parameters If a printer is configured through DHCP, IP Byte 1=new value→ appear Control Panel for Large-Format Printers EtherTalk is supported by HP DesignJet 650C To set the JOB Timeout parameter Current value→ appear Control Panel for Large-Format Printers Electrical FCC Statements Regulatory StatementsEuropean Community Declaration of Conformity Canada AustraliaJapan Vcci Class a RRL Statement Korea Taiwan Class a Chinese Safety Statement Link-Speed LEDs HP J4100A 10/100Base-TX Print Server Supported LinksLink Configuration jumpers Link Configuration Jumper SettingsLink Troubleshooting HP J4100A 10/100Base-TX Print Server Page 5969-3587