HP 400N manual Press ↓ to change NO* to YES, then press Enter to display

Page 73

6.Press ↓ to change NO* to YES, then press [Enter] to display

CFG NETWORK=YES.

7.At the CFG NETWORK=YES message, press ↑ repeatedly to scroll through the configuration options.

a.To change a network protocol setting (enable or disable), press [Enter], ↓, [Enter].

b.To configure network protocol parameters press [Enter], ↓ to select YES, then press [Enter] again.

To continue configuring protocol parameters, go to the appropriate sections that follow.

8.Press [Previous] and return to STATUS Ready.

9.To save the configuration, print a configuration plot by pressing the two arrow keys simultaneously. Your printer configuration is now active.

To configure parameters using HP JetDirect printer management software and to complete the print server configuration, see the HP JetDirect software installation guide included with the product.

HP DesignJet 4 Control Panel

Control Panel for Large-Format Printers 4-5

Image 73

Contents HP JetDirect 400N Page Hardware Installation Guide HP JetDirect 400N Print Server Safety Symbols HP J4105A HP J4106A HP JetDirect Print ServersIf you have a Token Ring card Quick InstallationVerify that the card was installed correctly Quick Installation Contents HP J4100A 10/100Base-TX Print Server Specifications and Regulatory StatementsHP JetDirect Print Server Card Introduction Network Types Connections Supported HP JetDirect Print Server Cards at a GlanceLPD Supported NetworksWhat You Need for Installation Installation HP LaserJet 5, 5M, and 5N printers Task 2. Before installing the card, verify the printer worksHP LaserJet 5Si, 5Si MX, 5Si NX, 5Si Mopier printers Press Enter. a self-test page will print HP Color LaserJet and Color LaserJet 5, 5M printersHP LaserJet 4, 4M, 4 Plus, and 4M Plus printers HP LaserJet 4Si and 4Si MX printers HP LaserJet 4V and 4MV printers Ready HP DeskJet 1200C and 1200 C/PS printers HP DeskJet 1600C, 1600CM, and 1600CN printersUtilities HP DesignJet 600 Series large-format printersInstallation Press -to print the Test HP CopyJet and CopyJet M color printer-copiersComponents face right for 4, 4M, 4 Plus, or 4M Plus Components face left for Color LaserJets including 5/5M To install the card into the HP LaserJet 4V and 4MV printers Components face right for HP LaserJet 5, 5M, 5N Installation Installing the HP JetDirect Print Server Card Installation To use the upper slot of an HP LaserJet 4Si or 4Si Remove faceplate from card Peel off label parts and attach cover plate to card Connect cards with customized plate at right Insertion of two cards into HP LaserJet 4Si/4SiMX For the HP J4100A JetDirect card RJ-45 Connect the power cord Turn on the power switch Installation Turn off the printer but leave the power cord plugged Installation Components face right for CopyJet CopyJet M printers Task 4. Verify the card was installed correctly Location of I/O Card Ready message on self-test pages What To Do Next Installing the HP JetDirect Print Server Card Printer Control Panel Enabling and Disabling Network Protocols To restore configuration default valuesProceed to Step To enable or disable network protocolsNovell NetWare Frame Types On an HP JetDirect Ethernet Card Configuring Novell NetWare Frame TypesTrsnap To configure a NetWare frame typeUsing the Control Panel for Printers To configure NetWare source routing Press Item until SRC RT=Source Routing* appears Configuring TCP/IP Parameters To configure TCP/IP parameters Shift keys To configure EtherTalk parameters Printer Control Panel Configuring the Timeout for End-of-Job Sensing Select To configure a NetWare frame type Configuring TCP/IP Parameters Using the Control Panel for Printers To configure EtherTalk parameters Using the Control Panel for Printers HP DesignJet 4 Control Panel Supported Network Protocols Press Enter. MIO Setup and CFG NETWORK=NO→ appear You will see CFG NETWORK=NO whenever you enter Press ↓ to change NO* to YES, then press Enter to display Detected For the 600 Series Printers MIO Setup and CFG IPX/SPX=YES→ appear Configuring TCP/IP Parameters If a printer is configured through DHCP, IP Byte 1=new value→ appear Control Panel for Large-Format Printers EtherTalk is supported by HP DesignJet 650C To set the JOB Timeout parameter Current value→ appear Control Panel for Large-Format Printers Electrical FCC Statements Regulatory StatementsEuropean Community Declaration of Conformity Canada AustraliaJapan Vcci Class a RRL Statement Korea Taiwan Class a Chinese Safety Statement Link-Speed LEDs HP J4100A 10/100Base-TX Print Server Supported LinksLink Configuration jumpers Link Configuration Jumper SettingsLink Troubleshooting HP J4100A 10/100Base-TX Print Server Page 5969-3587