HP 400N manual Press Enter. MIO Setup and CFG NETWORK=NO→ appear

Page 71

To enable or disable network protocols on the DesignJet 600 Series printers

1.Turn on the printer.

2.Verify that the printer displays STATUS and Ready to plot.

3.Press [Enter] until MENUS (FULL MENUS on the 650C printer) and Plot mgmt → appear.

4.Press ↑ repeatedly until MENUS and I/O setup→ appear.

5. Press [Enter] to access the MIO slot. I/O SETUP and Modular→ appear.

6.Press [Enter]. MIO SETUP and CFG NETWORK=NO→ appear.

7.To access the network configuration menu, press [Enter] to display CFG NETWORK and NO*.

8.Press ↑ to display: CFG NETWORK and YES.

9.Press [Enter]. MIO SETUP and CFG NETWORK=YES→ appear. You can now access the network configuration menu.

10.Press ↑ to display MIO SETUP and

NETWORK=<Current network protocol>.

11.Press [Enter]. <Current network protocol>* appears. An* next to a protocol denotes the current value.

12.Press ↑ repeatedly to scroll through the configuration options. When the protocol you wish to select is displayed, press [Enter] to save it. MIO SETUP and NETWORK=<New network protocol> appear.

13.Press [Previous] until Ready to plot is displayed. The printer is configured for the selected protocol.

Remember, if you enable a single protocol on the 600 Series printers, other protocols are turned off. You can restore default values by performing a cold reset on your printer.

HP DesignJet 4 Control Panel

Control Panel for Large-Format Printers 4-3

Image 71

Contents HP JetDirect 400N Page Hardware Installation Guide HP JetDirect 400N Print Server Safety Symbols HP J4105A HP J4106A HP JetDirect Print ServersIf you have a Token Ring card Quick InstallationVerify that the card was installed correctly Quick Installation Contents HP J4100A 10/100Base-TX Print Server Specifications and Regulatory StatementsHP JetDirect Print Server Card Introduction Network Types Connections Supported HP JetDirect Print Server Cards at a GlanceLPD Supported NetworksWhat You Need for Installation Installation HP LaserJet 5, 5M, and 5N printers Task 2. Before installing the card, verify the printer worksHP LaserJet 5Si, 5Si MX, 5Si NX, 5Si Mopier printers Press Enter. a self-test page will print HP Color LaserJet and Color LaserJet 5, 5M printersHP LaserJet 4, 4M, 4 Plus, and 4M Plus printers HP LaserJet 4Si and 4Si MX printers HP LaserJet 4V and 4MV printers Ready HP DeskJet 1200C and 1200 C/PS printers HP DeskJet 1600C, 1600CM, and 1600CN printersUtilities HP DesignJet 600 Series large-format printersInstallation Press -to print the Test HP CopyJet and CopyJet M color printer-copiersComponents face right for 4, 4M, 4 Plus, or 4M Plus Components face left for Color LaserJets including 5/5M To install the card into the HP LaserJet 4V and 4MV printers Components face right for HP LaserJet 5, 5M, 5N Installation Installing the HP JetDirect Print Server Card Installation To use the upper slot of an HP LaserJet 4Si or 4Si Remove faceplate from card Peel off label parts and attach cover plate to card Connect cards with customized plate at right Insertion of two cards into HP LaserJet 4Si/4SiMX For the HP J4100A JetDirect card RJ-45 Connect the power cord Turn on the power switch Installation Turn off the printer but leave the power cord plugged Installation Components face right for CopyJet CopyJet M printers Task 4. Verify the card was installed correctly Location of I/O Card Ready message on self-test pages What To Do Next Installing the HP JetDirect Print Server Card Printer Control Panel Enabling and Disabling Network Protocols To restore configuration default valuesProceed to Step To enable or disable network protocolsNovell NetWare Frame Types On an HP JetDirect Ethernet Card Configuring Novell NetWare Frame TypesTrsnap To configure a NetWare frame typeUsing the Control Panel for Printers To configure NetWare source routing Press Item until SRC RT=Source Routing* appears Configuring TCP/IP Parameters To configure TCP/IP parameters Shift keys To configure EtherTalk parameters Printer Control Panel Configuring the Timeout for End-of-Job Sensing Select To configure a NetWare frame type Configuring TCP/IP Parameters Using the Control Panel for Printers To configure EtherTalk parameters Using the Control Panel for Printers HP DesignJet 4 Control Panel Supported Network Protocols Press Enter. MIO Setup and CFG NETWORK=NO→ appear You will see CFG NETWORK=NO whenever you enter Press ↓ to change NO* to YES, then press Enter to display Detected For the 600 Series Printers MIO Setup and CFG IPX/SPX=YES→ appear Configuring TCP/IP Parameters If a printer is configured through DHCP, IP Byte 1=new value→ appear Control Panel for Large-Format Printers EtherTalk is supported by HP DesignJet 650C To set the JOB Timeout parameter Current value→ appear Control Panel for Large-Format Printers Electrical FCC Statements Regulatory StatementsEuropean Community Declaration of Conformity Japan Vcci Class a RRL Statement Korea Taiwan Class a AustraliaCanada Chinese Safety Statement Link-Speed LEDs HP J4100A 10/100Base-TX Print Server Supported LinksLink Configuration jumpers Link Configuration Jumper SettingsLink Troubleshooting HP J4100A 10/100Base-TX Print Server Page 5969-3587