HP 400N manual To configure NetWare source routing

Page 55

Configuring Novell NetWare Source Routing (Token Ring Cards Only)

You can select the method for Novell NetWare Token Ring source routing from the control panel. The possible routing methods are:

AUTO (default): Source routing is enabled if necessary.

OFF: All packets are sent without source routing—packets are received only if they originate from the same ring.

SINGLE R: All packets are sent with source routing. The Single Route method is used for broadcasts and when the route is unknown.

ALL RT: All packets are sent with source routing. The All Routes method is used for broadcasts and when the route is unknown.

You can configure the NetWare source routing if NetWare is enabled and you have installed a Token Ring print server.

To configure NetWare source routing

NOTE

For HP 2500C/CM Professional Series and

 

DesignJet ColorPro GA printers, see the “HP

 

2500C/CM Professional Series and DesignJet

 

ColorPro GA Control Panel” instructions at the end

 

of this chapter.

 

 

If you have not already done so, enable Novell NetWare (IPX/ SPX=ON*) by following the instructions described in “To enable or disable network protocols” in this chapter.

1.Take the printer offline by pressing [On Line] or [Go] to indicate offline.

2.Press [Menu] repeatedly until the following message is displayed on the control panel:

4 Series printers

AUX IO MENU

4 Plus and 4V Series printers

MIO MENU

Color LaserJet printers

MIO

CONFIG MENU

(Proceed to Step 4)

CFG

NETWORK=NO *

3 Printer Control Panel

Using the Control Panel for Printers 3-7

Image 55
Contents HP JetDirect 400N Page Hardware Installation Guide HP JetDirect 400N Print Server Safety Symbols HP J4105A HP J4106A HP JetDirect Print ServersIf you have a Token Ring card Quick InstallationVerify that the card was installed correctly Quick Installation Contents HP J4100A 10/100Base-TX Print Server Specifications and Regulatory StatementsHP JetDirect Print Server Card Introduction Network Types Connections Supported HP JetDirect Print Server Cards at a GlanceLPD Supported NetworksWhat You Need for Installation Installation HP LaserJet 5, 5M, and 5N printers Task 2. Before installing the card, verify the printer worksHP LaserJet 5Si, 5Si MX, 5Si NX, 5Si Mopier printers Press Enter. a self-test page will print HP Color LaserJet and Color LaserJet 5, 5M printersHP LaserJet 4, 4M, 4 Plus, and 4M Plus printers HP LaserJet 4Si and 4Si MX printers HP LaserJet 4V and 4MV printers Ready HP DeskJet 1200C and 1200 C/PS printers HP DeskJet 1600C, 1600CM, and 1600CN printersUtilities HP DesignJet 600 Series large-format printersInstallation Press -to print the Test HP CopyJet and CopyJet M color printer-copiersComponents face right for 4, 4M, 4 Plus, or 4M Plus Components face left for Color LaserJets including 5/5M To install the card into the HP LaserJet 4V and 4MV printers Components face right for HP LaserJet 5, 5M, 5N Installation Installing the HP JetDirect Print Server Card Installation To use the upper slot of an HP LaserJet 4Si or 4Si Remove faceplate from card Peel off label parts and attach cover plate to card Connect cards with customized plate at right Insertion of two cards into HP LaserJet 4Si/4SiMX For the HP J4100A JetDirect card RJ-45 Connect the power cord Turn on the power switch Installation Turn off the printer but leave the power cord plugged Installation Components face right for CopyJet CopyJet M printers Task 4. Verify the card was installed correctly Location of I/O Card Ready message on self-test pages What To Do Next Installing the HP JetDirect Print Server Card Printer Control Panel Enabling and Disabling Network Protocols To restore configuration default valuesProceed to Step To enable or disable network protocolsNovell NetWare Frame Types On an HP JetDirect Ethernet Card Configuring Novell NetWare Frame TypesTrsnap To configure a NetWare frame typeUsing the Control Panel for Printers To configure NetWare source routing Press Item until SRC RT=Source Routing* appears Configuring TCP/IP Parameters To configure TCP/IP parameters Shift keys To configure EtherTalk parameters Printer Control Panel Configuring the Timeout for End-of-Job Sensing Select To configure a NetWare frame type Configuring TCP/IP Parameters Using the Control Panel for Printers To configure EtherTalk parameters Using the Control Panel for Printers HP DesignJet 4 Control Panel Supported Network Protocols Press Enter. MIO Setup and CFG NETWORK=NO→ appear You will see CFG NETWORK=NO whenever you enter Press ↓ to change NO* to YES, then press Enter to display Detected For the 600 Series Printers MIO Setup and CFG IPX/SPX=YES→ appear Configuring TCP/IP Parameters If a printer is configured through DHCP, IP Byte 1=new value→ appear Control Panel for Large-Format Printers EtherTalk is supported by HP DesignJet 650C To set the JOB Timeout parameter Current value→ appear Control Panel for Large-Format Printers Electrical FCC Statements Regulatory StatementsEuropean Community Declaration of Conformity Canada AustraliaJapan Vcci Class a RRL Statement Korea Taiwan Class a Chinese Safety Statement Link-Speed LEDs HP J4100A 10/100Base-TX Print Server Supported LinksLink Configuration jumpers Link Configuration Jumper SettingsLink Troubleshooting HP J4100A 10/100Base-TX Print Server Page 5969-3587