HP 400N manual Link Troubleshooting

Page 93

Link Troubleshooting

If the HP J4100A JetDirect 10/100Base-TX print server does not successfully connect to the network, both LEDs will be off and a “LOSS OF CARRIER ERROR” will be indicated in the MIO section of the HP JetDirect self-test page.

NOTE

The HP J4100A JetDirect 10/100Base-TX print

 

server may require up to 10 seconds to establish a

 

connection on the network. You should wait up to

 

30 seconds before printing a configuration page to

 

verify a network connection.

 

 

Try the following troubleshooting procedures:

Verify cabling connections.

At the network device (such as a switching hub) that connects the print server to the network, configure the port for half- duplex operation. Then power-cycle the printer.

Manually set the link configuration both on the JetDirect print server and at the network device, ensuring that the link configurations are the same. (For example, if you set the HP JetDirect print server for 100TX Full-Duplex operation, the port on the network hub or switch must also be set to 100TX Full-Duplex operation.) Be sure to power-cycle the printer.

For additional assistance, contact your HP Customer Care center.

J4100A B 10/100Base-TX

HP J4100A 10/100Base-TX Print Server B-3

Image 93
Contents HP JetDirect 400N Page Hardware Installation Guide HP JetDirect 400N Print Server Safety Symbols HP J4105A HP J4106A HP JetDirect Print ServersIf you have a Token Ring card Quick InstallationVerify that the card was installed correctly Quick Installation Contents HP J4100A 10/100Base-TX Print Server Specifications and Regulatory StatementsHP JetDirect Print Server Card Introduction Network Types Connections Supported HP JetDirect Print Server Cards at a GlanceLPD Supported NetworksWhat You Need for Installation Installation HP LaserJet 5, 5M, and 5N printers Task 2. Before installing the card, verify the printer worksHP LaserJet 5Si, 5Si MX, 5Si NX, 5Si Mopier printers Press Enter. a self-test page will print HP Color LaserJet and Color LaserJet 5, 5M printersHP LaserJet 4, 4M, 4 Plus, and 4M Plus printers HP LaserJet 4Si and 4Si MX printers HP LaserJet 4V and 4MV printers Ready HP DeskJet 1200C and 1200 C/PS printers HP DeskJet 1600C, 1600CM, and 1600CN printersUtilities HP DesignJet 600 Series large-format printersInstallation Press -to print the Test HP CopyJet and CopyJet M color printer-copiersComponents face right for 4, 4M, 4 Plus, or 4M Plus Components face left for Color LaserJets including 5/5M To install the card into the HP LaserJet 4V and 4MV printers Components face right for HP LaserJet 5, 5M, 5N Installation Installing the HP JetDirect Print Server Card Installation To use the upper slot of an HP LaserJet 4Si or 4Si Remove faceplate from card Peel off label parts and attach cover plate to card Connect cards with customized plate at right Insertion of two cards into HP LaserJet 4Si/4SiMX For the HP J4100A JetDirect card RJ-45 Connect the power cord Turn on the power switch Installation Turn off the printer but leave the power cord plugged Installation Components face right for CopyJet CopyJet M printers Task 4. Verify the card was installed correctly Location of I/O Card Ready message on self-test pages What To Do Next Installing the HP JetDirect Print Server Card Printer Control Panel Enabling and Disabling Network Protocols To restore configuration default valuesProceed to Step To enable or disable network protocolsNovell NetWare Frame Types On an HP JetDirect Ethernet Card Configuring Novell NetWare Frame TypesTrsnap To configure a NetWare frame typeUsing the Control Panel for Printers To configure NetWare source routing Press Item until SRC RT=Source Routing* appears Configuring TCP/IP Parameters To configure TCP/IP parameters Shift keys To configure EtherTalk parameters Printer Control Panel Configuring the Timeout for End-of-Job Sensing Select To configure a NetWare frame type Configuring TCP/IP Parameters Using the Control Panel for Printers To configure EtherTalk parameters Using the Control Panel for Printers HP DesignJet 4 Control Panel Supported Network Protocols Press Enter. MIO Setup and CFG NETWORK=NO→ appear You will see CFG NETWORK=NO whenever you enter Press ↓ to change NO* to YES, then press Enter to display Detected For the 600 Series Printers MIO Setup and CFG IPX/SPX=YES→ appear Configuring TCP/IP Parameters If a printer is configured through DHCP, IP Byte 1=new value→ appear Control Panel for Large-Format Printers EtherTalk is supported by HP DesignJet 650C To set the JOB Timeout parameter Current value→ appear Control Panel for Large-Format Printers Electrical FCC Statements Regulatory StatementsEuropean Community Declaration of Conformity Australia CanadaJapan Vcci Class a RRL Statement Korea Taiwan Class a Chinese Safety Statement Link-Speed LEDs HP J4100A 10/100Base-TX Print Server Supported LinksLink Configuration jumpers Link Configuration Jumper SettingsLink Troubleshooting HP J4100A 10/100Base-TX Print Server Page 5969-3587