HP L25500 manual Restart the printer, Change the language of the front panel

Page 16

Basic setup options

Restart the printer

In some circumstances you may be advised to restart the printer. Please proceed as follows:

1.Press the Power button on the front panel to turn the printer off. Wait a few moments, and then press the Power button again. This should restart the printer. If it does not, continue with step 2.

2.Use the Reset button on the front panel. You will need a non-conductive implement with a narrow tip to press the Reset button. This normally has the same effect as pressing the Power button, but may work if the Power button does not.

3.If neither steps 1 nor 2 seems to have any effect, turn off the printer by using the power switch at the rear of the printer. Check that the residual current circuit breakers are in the up position.

4.Remove the power cords from the power sockets.

5.Wait for 10 seconds.

6.Reinsert the power cords into the power sockets and turn on the printer by using the power switch.

7.Make sure that the Power light on the front panel illuminates. If it does not, use the Power button to turn on the printer.

Change the language of the front panel

Two methods are available to change the language that is used for the front-panel menus and messages.

If you can understand the current front panel language, go to the front panel and select the icon, and then select Front panel options > Select language.

If you cannot understand the current front panel language, start with the printer powered off. At the front panel, press the OK button and hold it down. While holding down the OK button, press the Power button and hold it down. Continue to hold down both buttons until the green light on the left side of the front panel starts flashing, and then release both buttons. You can expect a delay of about one second. If the green light starts flashing without any delay, you may need to start again.

Whichever method you used, the language selection menu should now appear on the front panel.

Highlight your preferred language, and then press the OK button.

12 Chapter 3 Basic setup options

ENWW

Image 16
Contents HP Designjet L25500 Printer series Legal notices TrademarksTable of contents Accessories Printer specificationsSafety precautions General safety guidelinesIntroduction Electrical shock hazardFire hazard Heat hazardMechanical hazard Heavy substrate hazard Ink handlingPrinters main features Label ExplanationPrinters main components Front view 60-in printerRear view 60-in printer Take-up reel motor Front panelEmbedded Web Server Main tab Setup tabSupport tab Connectivity and software instructions Connection methodConnect to a network Connection type Speed Maximum cable length Other factorsPrinter setup options Basic setup optionsTurn the printer on and off Restart the printer Change the language of the front panelEmbedded Web Server setup options Change the language of the Embedded Web Server Overview Handle the substrateUse substrate Supported substrate families Load a roll onto the spindleSubstrate family Substrate types Load a roll onto the spindle Handle the substrate Load a roll into the printer Substrate Change loaded substrate Handle the substrate Exceptional procedure roll detached from spindle Normal procedure roll attached to spindleUnload a roll from the printer Use the take-up reel Load a roll onto the take-up reelHandle the substrate Handle the substrate Handle the substrate Enww Handle the substrate Unload a roll from the take-up reel Handle the substrate View information about the substrate Store the substrateAdd a new substrate type Download substrate presetsSummary Substrate family Description Select printer settings and color profileSubstrate family Paper-Solvent Setting Description If too low If too highHP Photorealistic 100 Substrate at the beginning Key Select the number of passesVinyl Check the ink quantity Coalescence, grain Color profiles Color calibrationFaster printing Ink system components Handle the ink systemInk cartridges Printheads Printhead cleaning container Printhead cleaning cartridgeInk funnel Work with ink system components Ink system tipsReplace an ink cartridge Remove an ink cartridge Work with ink system components Insert an ink cartridge Replace a printhead Remove a printhead Handle the ink system Insert a printhead Handle the ink system Handle the ink system Replace the printhead cleaning kit Remove the printhead cleaning cartridgeHandle the ink system Insert the printhead cleaning cartridge Replace the ink funnel Handle the ink system Order ink supplies CartridgePrinthead cleaner PrintheadPrinter states Print optionsChange margins Request the printers internal prints Order accessories AccessoriesName Functional specifications Printer specificationsMinimum Maximum Physical specifications Memory specificationsPower specifications Ecological specificationsEnvironmental specifications Acoustic specificationsGlossary AirflowLED Margins IndexOrder Enww