HP L25500 manual Heat hazard, Fire hazard, Mechanical hazard

Page 6

Introduction

To avoid the risk of electric shock:

Do not attempt to dismantle the drying and curing modules or the electrical control cabinet.

Do not remove or open any other closed system covers or plugs.

Do not insert objects through slots in the printer.

NOTE: A blown fuse may indicate malfunctioning electrical circuits within the system. Call your service representative, and do not attempt to replace the fuse yourself.

Heat hazard

The drying and curing subsystems of the printer operate at high temperatures and can cause burns if touched. To avoid personal injury, take the following precautions.

Do not touch the internal enclosures of the printer's drying and curing modules. Even after opening the window latch that disconnects drying and curing power, the internal surfaces could be hot.

Take special care when accessing the substrate path.

Fire hazard

The drying and curing subsystems of the printer operate at high temperatures. Call your service representative if the printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) is repeatedly tripped.

To avoid the risk of fire, take the following precautions.

Use the power supply voltage specified on the nameplate.

Connect the power cords to dedicated lines, each protected by a branch circuit breaker according to the rating of the wall socket. Do not use a power strip (relocatable power tap) to connect both power cords.

Use only the power cords supplied by HP with the printer. Do not use a damaged power cord. Do not use the power cords with other products.

Do not insert objects through slots in the printer.

Take care not to spill liquid on the printer.

Do not use aerosol products that contain flammable gases inside or around the printer.

Do not block or cover the openings of the printer.

Do not attempt to dismantle the drying or curing module, or the electrical control cabinet.

Load substrates that can be used at an operating temperature of up to 125°C (257°F), and have auto-ignition temperatures above 250°C (482°F).

Mechanical hazard

The printer has moving parts that could cause injury. To avoid personal injury, take the following precautions when working close to the printer.

Keep your clothing and all parts of your body away from the printer's moving parts.

Avoid wearing necklaces, bracelets and other hanging objects.

If your hair is long, try to secure it so that it will not fall into the printer.

Take care that sleeves or gloves do not get caught in the printer's moving parts.

2 Chapter 1 Introduction

ENWW

Image 6
Contents HP Designjet L25500 Printer series Legal notices TrademarksTable of contents Accessories Printer specificationsIntroduction Safety precautionsGeneral safety guidelines Electrical shock hazardHeat hazard Fire hazardMechanical hazard Heavy substrate hazard Ink handlingPrinters main features Label ExplanationPrinters main components Front view 60-in printerRear view 60-in printer Take-up reel motor Front panelEmbedded Web Server Setup tab Main tabSupport tab Connect to a network Connectivity and software instructionsConnection method Connection type Speed Maximum cable length Other factorsBasic setup options Printer setup optionsTurn the printer on and off Restart the printer Change the language of the front panelEmbedded Web Server setup options Change the language of the Embedded Web Server Handle the substrate OverviewUse substrate Load a roll onto the spindle Supported substrate familiesSubstrate family Substrate types Load a roll onto the spindle Handle the substrate Load a roll into the printer Substrate Change loaded substrate Handle the substrate Normal procedure roll attached to spindle Exceptional procedure roll detached from spindleUnload a roll from the printer Use the take-up reel Load a roll onto the take-up reelHandle the substrate Handle the substrate Handle the substrate Enww Handle the substrate Unload a roll from the take-up reel Handle the substrate View information about the substrate Store the substrateDownload substrate presets Add a new substrate typeSummary Select printer settings and color profile Substrate family DescriptionSubstrate family Setting Description If too low If too high Paper-SolventHP Photorealistic 100 Substrate at the beginning Select the number of passes KeyVinyl Check the ink quantity Coalescence, grain Color calibration Color profilesFaster printing Handle the ink system Ink system componentsInk cartridges Printheads Printhead cleaning cartridge Printhead cleaning containerInk funnel Ink system tips Work with ink system componentsReplace an ink cartridge Remove an ink cartridge Work with ink system components Insert an ink cartridge Replace a printhead Remove a printhead Handle the ink system Insert a printhead Handle the ink system Handle the ink system Replace the printhead cleaning kit Remove the printhead cleaning cartridgeHandle the ink system Insert the printhead cleaning cartridge Replace the ink funnel Handle the ink system Order ink supplies CartridgePrinthead cleaner PrintheadPrint options Printer statesChange margins Request the printers internal prints Accessories Order accessoriesName Printer specifications Functional specificationsMinimum Maximum Power specifications Physical specificationsMemory specifications Ecological specificationsEnvironmental specifications Acoustic specificationsGlossary AirflowLED Index MarginsOrder Enww