HP RP5 5810 manual Computer Operating Guidelines and Routine Care

Page 76

DComputer Operating Guidelines, Routine Care and Shipping Preparation

Computer Operating Guidelines and Routine Care

Follow these guidelines to properly set up and care for the computer and monitor:

Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold.

Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides of the computer and above the monitor to permit the required airflow.

Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place the keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also restricts airflow.

Never operate the computer with the access panel or any of the expansion card slot covers removed.

Do not stack computers on top of each other or place computers so near each other that they are subject to each other’s re-circulated or preheated air.

If the computer is to be operated within a separate enclosure, intake and exhaust ventilation must be provided on the enclosure, and the same operating guidelines listed above will still apply.

Keep liquids away from the computer and keyboard.

Never cover the ventilation slots on the monitor with any type of material.

Install or enable power management functions of the operating system or other software, including sleep states.

Turn off the computer before you do either of the following:

Wipe the exterior of the computer with a soft, damp cloth as needed. Using cleaning products may discolor or damage the finish.

Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign matter can block the vents and limit the airflow.

70 Appendix D Computer Operating Guidelines, Routine Care and Shipping Preparation

Image 76
Contents Hardware Reference Guide Product Notice About This Book Iv About This Book Table of contents Preventing Electrostatic Damage Grounding Methods Product Features Standard Configuration FeaturesDrive configuration may vary by model Front Panel ComponentsRear Panel Components 2Rear Panel ComponentsChanging from Desktop to Tower Configuration Installing the Optional Port Cover Serial Number Location 7Cable RoutingHardware Upgrades Removing the Computer Access Panel Replacing the Computer Access PanelRemoving the Front Bezel Installing an Optical Drive Bezel 5Installing the Optical Drive Bezel Hardware UpgradesRemoving a Bezel Blank Replacing the Front BezelDIMMs Installing Additional MemoryDDR3-SDRAM DIMMs Populating Dimm Sockets 1DIMM Socket LocationsInstalling DIMMs Page Page Installing a Half-Height Expansion Card 2System Board Expansion Slot LocationsInstalling a 12-Volt Powered USB Expansion Card 1324-volt and 12-volt Powered USB ConnectorsPage Page Page Page Page Installing a Second DisplayPort Expansion Card Page Page Installing a Full-Height Expansion Card 4Riser Card ConfigurationsInstalling a Powered Serial Port Expansion Card 25Powered Serial PortsPage Page Close the expansion card retention latch Configuring Powered Serial Ports Replacing the Riser CardPage 35Removing the Lower Expansion Slot Cover Hardware Upgrades 37Removing the Riser Card Bracket Replacing the Riser Card 39Installing the Riser Card Hardware Upgrades Page Close the expansion card retention latch Installing and Removing Drives Drive Positions45Extra Guide Screw Locations System Board Drive Connections 8System Board Drive ConnectionsRemoving an Optical Drive from the 5.25-inch Drive Bay Page Installing an Optical Drive into the 5.25-inch Drive Bay 50Removing the 5.25-inch DrivePage Page Page Removing a Secondary Hard Drive from the 3.5-inch Drive Bay Page 60Installing a Secondary Hard Drive Hardware Upgrades Page 63Raising the Power Supply Hardware Upgrades Page Page 67Installing the Hard Drive Installing and Removing Drives Page Replacing the Battery Type69Removing and Replacing a Coin Cell Battery Type Installing a Security Lock HP Keyed Cable LockPadlock HP Business PC Security Lock Page Page Page Front Bezel Security Page Optional Integration Tray and Accessories Page Preventing Electrostatic Damage Grounding MethodsComputer Operating Guidelines and Routine Care Optical Drive Precautions CleaningSafety Shipping PreparationIndex USB