Sterling SDA AP-1 specifications Identifying Controller Screens, Main Menu Screen

Page 36

•Copyright Information

•PLC Version

•Display Version

After approximately 10-12 seconds the controller will flash to the Dryer Status Screen shown on the previous page.

4-4 Identifying Controller Screens

Main Menu Screen

(Main Menu Screen)

The MAIN MENU provides information on the following system parameters:

•DRYER

•ALARMS

•HELP

•SYSTEM

•LOG OFF

Press the DRYER MENU button to return to the next section of dryer functions.

Typical Dryer Screens

(Dryer Status Screen)

(Shown at Controller Power Up) (Looking at the screen from Left to Right)

The SETPOINT button allows the operator to set the process air temperature.

The ACTUAL value will give you a reading of what the actual process air temperature is entering the drying hopper.

Large Dehumidifying Dryers

Controls

36

Image 36

Contents SDA Large AP-1 Control Dehumidifying Dryer Shipping Info Unpacking and InspectionEvent of Shipping Damage If the Shipment is Not CompleteReturns Table of Contents Operation Troubleshooting Safety How to Use This ManualSafety Symbols Used in this Manual Dryer Safety Tags Description Responsibility General ResponsibilityOperator Responsibility Maintenance Responsibility Reporting a Safety Defect Functional Description Models Covered in This ManualGeneral Description Process/Regeneration Cycle Sequence of OperationStandard Features Auto Start TimerMechanical Features Electrical FeaturesOptions Dewpoint ExtendClosed-Loop Regeneration Drawings and Diagrams Optional dryer dust collector Aftercooler Design Specifications Process AftercoolerProcess Air Dust Collector Process Air Dust Collector Recommended Temperature Settings Material Overdrying ProtectionMechanical Options Electrical OptionsController Options Safety Devices and Interlocks Safety Circuit StandardsSafety Device Lock-Outs Fail Safe OperationPage Dimensions and Specifications Denotes availability Mechanical Options Denotes availabilityDenotes availability Mechanical Installation Uncrating the EquipmentRigging and Placing Unit Making Electrical ConnectionsMaking Gas Line Connections Gas-Fired Models Only DescriptionChecking for Proper Blower Rotation Checking Blower RotationMaking Dryer/Drying Hopper Process Air Connections Dryer/Drying Hopper Process Air ConnectionsProcess Air Heater on Drying Hopper Large Dehumidifying Dryers Mechanical Installation Connecting Aftercooler/Precooler Cooling Water Optional Aftercooler Components & Flow RatesUsing the Drying Hopper Air Trap Drying Hopper Air TrapControls Controller DescriptionProcess Air Temperature and Conveying Process Controller Dryer Status Screen Startup ScreenDryer Alarms Help System LOG OFF Identifying Controller ScreensMain Menu Screen Setting Values Dryer Status Dryer Setup Over DRY Protect Alarms Auto Tune Dryer MenuAuto Start Main Menu Dryer Setup Screen 2 Dryer Setup Screen 3Dryer Setup Screen 4 Overdry Protection Overdry Protection Screen 1Overdry Protection Screen 2 Alarm History Screen AutotuneProcess AutoTune Screen DEW Point Setup Dew Point Setup ScreenAutostart Timer Screen Auto StartSystem Setup SET Clock Hour Meters Alarm History Status Help MenuHelp Menu Screen System MenuSystem Backup Service Menu Main Menu System Setup System Setup ScreenLOW Level Detection Setup Clock Menu Screen Autostart Clock ScreenHour Meter Screen Input StatusInput Status Screen Output StatusSystem Backup Screen ServiceService Menu Screen Alarm Screens Redundant Safety Controller Display Alarm Screen ExampleSetting the Redundant Safety Controller Always put your set point to 30F above set pointLarge Dehumidifying Dryers Controls Operation Start-upUsing the Dryer Status Screen Alarms Alarm DescriptionsShutdown Maintenance Maintenance SchedulePhotocopy this page for your maintenance records Preventative Maintenance Cleaning or Replacing the Process Air FiltersCleaning or Replacing the Regeneration Filter Calibrating the Dirty Filter AlarmChecking the Dewpoint Control System Corrective Maintenance Symptoms of Worn Out DesiccantReplacing the Desiccant Desiccant Tower Assembly Replacing the Process Heater Electric DryersProcess Heater Box Assembly Replacing the Regeneration Heater Electric DryersRegeneration Heater Box Assembly Troubleshooting Basic TroubleshootingIntroduction Large Dehumidifying Dryers Troubleshooting Determining Temperature Controller Errors or Sensor Errors Using a ThermocoupleUsing a Platinum Resistance Thermometer Warranty Returns AppendixReturned Material Policy Credit ReturnsTechnical Specifications Annex B InformationSpare Parts List Level 3 Mechanical Components Dryer Identification Serial Number Tag Located on back of DryerService Department Technical AssistanceParts Department Sales Department