HP 620n Fast Ethernet Print Server Manual, Settings, Default IP, Primary DNS, Secondary, Dns

Page 41

Table C-2. EIO Graphical Control Panel Menu (3 of 5)

Menu Item

Options

Description of settings

 

 

 

 

MANUAL

(Available only if CONFIG METHOD is set

 

SETTINGS

to MANUAL) Configure parameters

 

 

directly from the printer control panel:

 

 

IP ADDRESS n.n.n.n: The unique IP

 

 

address of the printer, where n is a

 

 

value from 0 to 255.

 

 

SUBNET MASK m.m.m.m: The

 

 

subnet mask for the printer, where m

 

 

is a value from 0 to 255.

 

 

SYSLOG SERVER n.n.n.n: The IP

 

 

address of the syslog server used to

 

 

receive and log syslog messages.

 

 

DEFAULT GATEWAY n.n.n.n: The

 

 

IP address of the gateway or router

 

 

used for communications with other

 

 

networks.

 

 

IDLE TIMEOUT: The time period, in

 

 

seconds, after which an idle TCP print

 

 

data connection is closed (default is

 

 

270 seconds, 0 disables the timeout).

 

 

 

 

DEFAULT IP

Specify the IP address to default to when

 

 

the print server is unable to obtain an IP

 

 

address from the network during a forced

 

 

TCP/IP reconfiguration (for example,

 

 

when manually configured to use BOOTP

 

 

or DHCP).

 

 

AUTO IP: A link-local IP address

 

 

169.254.x.x will be set.

 

 

LEGACY: The address 192.0.0.192

 

 

will be set consistent with older

 

 

Jetdirect products.

 

 

 

 

PRIMARY DNS

Specify the IP address (n.n.n.n) of a

 

 

Primary DNS Server.

 

 

 

 

SECONDARY

Specify the IP address (n.n.n.n) of the

 

DNS

Secondary Domain Name System (DNS)

 

 

Server.

 

 

 

ENWW

HP Jetdirect EIO Control Panel Menus 41

Image 41
Contents HP Jetdirect Print Server Page Setup Guide HP Jetdirect Print Server Model 620n EIO Applicable Products Table of Contents HP Jetdirect Solutions Summary HP Jetdirect EIO Print Server IntroductionTypical HP Jetdirect Print Server Installation What You Need For Help Product Accessibility Installation Procedures Verify Printer Operation RJ-45 Remove Power to Printer, Install the HardwareVerify Jetdirect Print Server Operation See in this guide for link configuration Configuration Tools If Required, Configure Jetdirect With Your Network SettingsMenus Add the Printer to Your Network Server or System Adding a Printer to Your System ConfigurationInstallation Procedures Client-Server Networks Unix Networks 10/100Base-TX Link Configuration Troubleshooting Tools HP Jetdirect ConfigurationLink-Speed LEDs OFF Autonegotiation is disabled, 10/100TX On Autonegotiation is enabled, orConfiguration has been manually set Port SelectControlling Network Protocols Resetting to Factory DefaultsEnabling or Disabling Network Protocols Troubleshooting Tools Client-Server printing Peer-to-Peer printingNetwork Addresses Network ProtocolsSetting Up Your Network Printer Introduction to Network Printing Embedded HP Jetdirect services HP Jetdirect Solutions Summary Tools OverviewTCP/IP Supported Network ProtocolsIPX/SPX DLC/LLCHP Installation Software HP Jetdirect Solutions Summary HP Jetdirect EIO Control Panel Menus Introduction Classic Control Panel CFG TCP/IP= CFG LINK= CFG IPX/SPX=WEB= HttpsHost Name TCP/IP EnableGraphical Control Panel Method ConfigDhcp Release Dhcp RenewDefault IP SettingsManual Primary DNSAppltalk Enable IPX/SPX EnableDLC/LLC Enable Proxy ServerSecure ResetWEB SecurityHP Jetdirect EIO Control Panel Menus Specifications and Regulatory Statements For EU immunity compliance, see ElectromagneticFCC Statements Regulatory StatementsThis equipment complies with Australian EMC requirements European CommunityHP Product Duration of Limited Warranty Warranty ServiceYour Authorized Dealer Firmware Upgrades HP Support and Service HP Support OnlineHP Support By Phone Page 620SGEN