HP 620n Fast Ethernet Print Server manual Proxy Server, Proxy Port, IPX/SPX Enable, Frame Type

Page 42

Table C-2. EIO Graphical Control Panel Menu (4 of 5)

Menu Item

Options

Description of settings

 

 

 

 

PROXY SERVER

Specifies the proxy server to be used by

 

 

embedded applications in your

 

 

printer/MFP. A proxy server is typically

 

 

used by network clients for Internet

 

 

access. It caches Web pages, and

 

 

provides a degree of Internet security, for

 

 

those clients.

 

 

To specify a proxy server, enter its IP

 

 

address or fully-qualified domain name.

 

 

The name can be up to 255 octets.

 

 

For some networks, you may need to

 

 

contact your Independent Service

 

 

Provider (ISP) for the proxy server

 

 

address.

 

 

 

 

PROXY PORT

Enter the port number used by the proxy

 

 

server for client support. The port number

 

 

identifies the port reserved for proxy

 

 

activity on your network, and can be a

 

 

value from 0 to 65535.

 

 

 

IPX/SPX

ENABLE

ON: Enable the IPX/SPX protocol.

 

 

OFF: Disable the IPX/SPX protocol.

 

 

 

 

FRAME TYPE

Selects the frame type setting for your

 

 

network.

 

 

AUTO: (Default) automatically sets

 

 

and limits the frame type to the first

 

 

one detected.

 

 

EN_8023, EN_II, EN_8022,

 

 

EN_SNAP are frame type selections

 

 

for Ethernet networks.

 

 

 

APPLTALK

ENABLE

ON: Enable the AppleTalk protocol.

 

 

OFF: Disable the AppleTalk protocol.

 

 

 

DLC/LLC

ENABLE

ON: Enable the DLC/LLC protocol.

 

 

OFF: Disable the DLC/LLC protocol.

 

 

 

ENWW

HP Jetdirect EIO Control Panel Menus 42

Image 42
Contents HP Jetdirect Print Server Page Setup Guide HP Jetdirect Print Server Model 620n EIO Applicable Products Table of Contents HP Jetdirect Solutions Summary Introduction HP Jetdirect EIO Print ServerTypical HP Jetdirect Print Server Installation What You Need For Help Product Accessibility Installation Procedures Verify Printer Operation Remove Power to Printer, Install the Hardware RJ-45Verify Jetdirect Print Server Operation See in this guide for link configuration If Required, Configure Jetdirect With Your Network Settings Configuration ToolsMenus Adding a Printer to Your System Configuration Add the Printer to Your Network Server or SystemInstallation Procedures Client-Server Networks Unix Networks Troubleshooting Tools HP Jetdirect Configuration 10/100Base-TX Link ConfigurationLink-Speed LEDs Configuration has been manually set On Autonegotiation is enabled, orOFF Autonegotiation is disabled, 10/100TX Port SelectResetting to Factory Defaults Controlling Network ProtocolsEnabling or Disabling Network Protocols Troubleshooting Tools Peer-to-Peer printing Client-Server printingNetwork Protocols Network AddressesSetting Up Your Network Printer Introduction to Network Printing HP Jetdirect Solutions Summary Tools Overview Embedded HP Jetdirect servicesIPX/SPX Supported Network ProtocolsTCP/IP DLC/LLCHP Installation Software HP Jetdirect Solutions Summary HP Jetdirect EIO Control Panel Menus Introduction Classic Control Panel CFG TCP/IP= WEB= CFG IPX/SPX=CFG LINK= HttpsTCP/IP Enable Graphical Control PanelHost Name Dhcp Release ConfigMethod Dhcp RenewManual SettingsDefault IP Primary DNSDLC/LLC Enable IPX/SPX EnableAppltalk Enable Proxy ServerWEB ResetSecure SecurityHP Jetdirect EIO Control Panel Menus Specifications and Regulatory Statements Electromagnetic For EU immunity compliance, seeRegulatory Statements FCC StatementsEuropean Community This equipment complies with Australian EMC requirementsWarranty Service HP Product Duration of Limited WarrantyYour Authorized Dealer HP Support and Service HP Support Online Firmware UpgradesHP Support By Phone Page 620SGEN