HP 449298-001 manual Supported actions delete, help, set, show

Page 11

Supported actions: delete, help, set, show

Item

Description

 

 

delete domain

Delete the existing Virtual Connect domain configuration.

 

Deleting the domain removes the entire Virtual Connect domain configuration

 

and resets it back to the original defaults. After the domain has been deleted,

 

you are logged out and the Virtual Connect Manager resets.

 

 

Syntax

delete domain [-quiet]

 

 

Examples:

 

 

 

 

->delete domain

 

Deletes the Virtual Connect domain configuration and prompts for user

 

confirmation

 

 

 

->delete domain -quiet

 

Deletes the Virtual Connect domain quietly without prompting for user

 

confirmation (primarily used in automated scripting scenarios)

 

 

Item

Description

 

 

set domain

Modify domain configuration properties

 

 

Syntax

set domain [Name=<NewName>] [DomainIp=<EnabledDisabled>]

 

[IpAddress=<IPAddress>] [SubnetMask=<mask>]

 

[Gateway=<Gateway>] [MacType=<VC-DefinedFactory-Default

 

User-Defined>] [MacPool=<1-64>] [MacStart=<address>]

 

[MacEnd=<address>] [WwnType=< VC-DefinedFactory-Default>]

 

[WwnPool=<1-64>]

 

 

Properties:

 

 

 

Name

The new name of the domain. Valid characters include alphanumeric, "_", and

 

".". The maximum length of the name is 64 characters.

 

 

DomainIP

Enables or disables the Virtual Connect domain IP address. If enabled, then a

 

valid IP address subnet mask must be configured. If disabled, then DHCP is used

 

to obtain a valid IP address.

 

Enabling domain IP address configuration, or changing the domain IP address

 

can cause a temporary loss of connectivity to the Virtual Connect Manager. Use

 

caution when changing these settings.

 

 

IpAddress

A valid IP address to use for the domain IP address configuration

 

 

SubnetMask

A valid subnet mask for the domain IP address configuration

 

 

Gateway

A valid gateway address for the domain IP address configuration

 

 

MacType

The type of MAC address source to use for assignment. Valid values include VC-

 

Defined, Factory-Default, and User-Defined

 

 

MacPool

The pre-defined MAC pool to use for address assignment. Valid values include

 

integers 1-64. This property is only valid if the MacType is set to "VC-Defined". If

 

not specified, the default pool ID is 1.

 

 

MacStart

The starting MAC address in a custom user-defined range. This property is only

 

valid if the MacType is set to "User-Defined".

 

 

MacEnd

The ending MAC address in a custom user-defined range. This property is only

 

valid if the MacType is set to "User-Defined".

 

 

WwnType

The type of WWN address source to use for assignment. Valid values include

 

VC-Defined and Factory-Default.

 

 

Command line 11

Image 11
Contents HP Virtual Connect Manager Command Line Interface User Guide Audience assumptions Contents Technical support Virtual Connect overview Command line overviewIntroduction Options Command line syntaxSubcommand managed element parameters options properties ParametersProperties CLI command execution modesRemote access to the Virtual Connect Manager Managed elements Command lineSubcommands Domain DevicebaySupported actions delete, help, set, show Enclosure Supported actions add, help, remove, set Enet-connectionEthernetMAC Network=SomeNetwork2 PXE=enabledAddressType=Factory-Default AddressTypeExternal-manager Fabric Fc-connection Firmware Support actions help, show, updateInterconnect IgmpLdap Supported actions add, help, remove, set, show Ldap-groupMac-cache Network Profile Assign profile Add profile MyNewProfile2 -NoDefaultEnetConnAdd profile MyNewProfile2 -NoDefaultFcConn Add profile MyNewProfileServer Supported actions help, poweroff, poweron, reboot, showPoweroff server enc02 -ForceOnTimeout Poweroff server enc02Poweroff server enc02 -Force Poweroff server enc0Stackinglink Uplinkport StatusSystemlog Set uplinkport enc012 Network=MyNetwork Speed=1Gb Set uplinkportSet uplinkport PortID Network=NetworkName Speed=Auto10Mb100Mb1GbDisabledUplinkset User Remove user steve Set user steve Password=fgY87hHlSet user steve Password Set user bill Password=HGtwf7272562Version Help subsystemVcm Command line Interactive user output format Output formatBrad Domain Brad Mills Brad.mills@hp.com True Server Scriptable output format Command line Ssh 192.168.0.120 login as Administrator Configuring the Virtual Connect domain using the CLIBasic configuration Ssh 192.168.0.120 login as Administrator passwordImporting an enclosure Domain setupSetting the domain name Configuring local usersRemove user Add user bob password=fhkjdhfk privileges=domain,networkSet user bob fullname=Bob J Smith enabled=false Remove user bobConfiguring MAC Address ranges Network setupConfiguring Ldap authentication support for users Assigned MAC addresses Creating a shared uplink port set Creating an enet-networkAdding uplink ports to an enet-network Creating a network that uses a shared uplink port set Fibre Channel setupConfiguring WWN address ranges Adding uplink ports to a shared uplink port setSet fabric name=MyNewName portspeed=4Gb Server Profile setupModifying FC fabric properties Displaying FC fabricsConfiguring the Virtual Connect domain using the CLI Adding FC fabric connections to a server profile Configuring Igmp settingsCreating server profiles Adding enet-network connections to a profileLogging out of the CLI Configuring MAC cache failover settingsSet mac-cache enabled=true refresh=10 Common management operationsReset vcm Reset vcm -failover Resetting the Virtual Connect ManagerVirtual Connect Manager not found at this IP address HP contact information Technical supportBefore you contact HP Igmp Acronyms and abbreviationsPXE Index Index