HP A4800A manual Cable Specifications, A5068A Scsi Cable Kit Description Part Number

Page 11

HP A4800A Adapter Overview

Cable Specifications

Cable Specifications

The A4800A adapter supports High Voltage Differential (HVD) SCSI connections only. Internal cables for interconnection with the embedded CD-ROM drive and DAT tape drive are provided in the system.

The A5068A SCSI cable kit is required when connecting the A4800A adapter to internal, non-embedded SCSI devices. Table 1-2 below shows the parts that make up the A5068A kit.

Table 1-2

A5068A SCSI Cable Kit

 

 

 

 

 

Description

Part

 

Number

 

 

 

 

 

 

10-inch SCSI shielded cable with back

A4700-67086

 

shell

 

 

 

 

 

68-pin HD SCSI terminator

A4700-67098

 

 

 

For more information on connecting the adapter to internal disk and tape devices, refer to the appropriate disk drive or tape drive product manual.

For V-Class Systems

If you are connecting external SCSI devices to an A4800A adapter installed in a V-Class system, you must use one of the cables shown in Table 1-3 below. Note that cables are normally supplied with the peripheral device.

Table 1-3

Cables for Connecting External SCSI Devices to the A4800A

 

Adapter in V-Class Systems

 

 

 

 

 

 

 

Description

Product

Option

 

Number

 

 

 

 

 

 

 

 

5-meter 68-pin HD/68-pin HD Male

A3401A

875

 

inline terminator SCSI cable for

 

 

 

V-Class

 

 

 

 

 

 

Chapter 1

11

Image 11
Contents Manufacturing Part Number A3725-96031 E0201 HP A4800A PCI FWD Scsi Host Bus AdapterLegal Notices Page Page HP A4800A Adapter Overview HP A4800A Adapter Overview About the A4800A Adapter A4800A PCI Ultra HVD Scsi Host Bus Adapter Below is a drawing of the A4800A adapterFeatures Supported HP 9000 Servers A5068A Scsi Cable Kit Description Part Number Cables for Connecting External Scsi Devices to the A4800ACable Specifications Adapter in V-Class Systems Description Product Option Number Installing the A4800A Adapter Installing the A4800A Adapter Preparing for Installation Connecting to External Scsi Devices Handling the A4800A Adapter Important Terms and Concepts Looking at Adapter InstallationOlar Important Terms MeaningPlanning and Preparation Card Compatibility Step A4800-60001 Default Scsi Attribute ValuesAttribute Default Value OLA/R Restrictions for the A4800ALooking at Adapter Installation Reassemble the server Scsi Connecting Scsi Peripheral Devices12.5 Fast Scsi Fast Wide Connecting Scsi Peripheral Devices Terminating the A4800A Adapter Setting Scsi IDs Scsi Device Record of Scsi IDsVerifying Installation HP e3000 Troubleshooting Troubleshooting General Procedure Clearpim Checking Scsi Bus CompatibilityDisplaying Transfer Rates Scsi CommandSetting Transfer Rates Displaying Scsi IDs Setting Scsi IDs Using Support Tools Manager STM Contacting Your Hewlett-Packard Representative Contacting Your Hewlett-Packard Representative Contacting Your Hewlett-Packard Representative Chapter Scsi Sense Codes MPE/iX Status Meaning Code Table A-1 Scsi Status CodesSense Meaning Key Table A-2 Scsi Sense KeysAddition Qualifier Meaning Al Sense Code Table A-3 Scsi Additional Sense Code/Qualifier Code PairsLogical unit not ready, cause not ID crc or ecc error Recorded entity not found Recovered data with error correction Applied Logical block address out of range Commands cleared by another initiator Sequential positioning error Target operation conditions have Changed Write append error Log exception 0x69 0x00 Regulatory Information FCC Statement For U.S.A. Only Regulatory StatementsVcci Statement Japan Declaration of Conformity