Roberts Gorden UHA[X][S] 125 External Controls, Complete Start-Up, Instruction to the User

Page 38

UHA LOW PROFILE UNIT HEATER INSTALLATION OPERATION AND SERVICE MANUAL

Heat exchanger could be damaged. Warranty will not cover damage to the heat exchanger if operated improperly. Only use the disconnect switch for turning off heater for service or during off-season.

10.2.5 External Controls

External controls may include time switch, interlock switch, room thermostat and frost thermostat. Operate each control to ensure that they function correctly. Set the switches (if fitted) and thermostat(s) to the users’ requirements.

10.3 Complete Start-Up

Ensure that all covers are fitted correctly and all test points are properly sealed.

10.3.1 Instruction to the User

Explain the controls of the heater to the user including how to turn it on and off, using the controls fitted on site.

Give this manual to the user.

Ensure that the user is shown and understands the importance of maintaining clearances to combustibles on Page 7, Figure 4 and the user instructions on Page 6, Section 3 and Page 33, Section 11 and all warnings defined in this manual.

32

Image 38

Contents UHA-Series Tubular Unit Heaters Low Profile Range Installation, Operation & Service ManualCombat Models UHAXS 30, 45, 60, 75, 100,Page Printed in U.S.A TABLE OF CONTENTS2008 Roberts-GordonLLC Page TABLE OF FIGURES Page 1.2 Safety Labels and Their Placement SECTION 1: HEATER SAFETY1.1 Manpower Requirements Figure 1: UHA 30 - 45 Label Placement For separated combustion units onlyFigure 2: UHA 60 - 75 Label Placement For separated combustion units onlyFigure 3: UHA 100 - 125 Label Placement For separated combustion units only2.2 Corrosive Chemicals SECTION 2: INSTALLER RESPONSIBILITY2.1 Wall Tag 2.3 National Standards and Applicable Codes3.5 Clearances to Combustibles 3.4 Minimum Required Installation Clearances3.2 Manufactured Units 3.6 Ventilation3.9 Vent 3.7 Gas Supply3.8 Electrical Supply 4.3 Parking Structures and Repair Garages 4.1 Gas Codes4.2 Aircraft Hangars 4.4 Electrical4.6 High Altitude 5.3 Wall Mounting SECTION 5: MAJOR COMPONENTS 5.1 General5.2 Shelf Mounting and Suspension Crush Hazard Use 3/8 threaded rod minimumExisting cabinet screws must be re-used Figure 5: Suspension MethodsFigure 6: Shelf-MountingMethods Wall Shelf Mounting Bracket Kit DescriptionPart Number Descriptionlouver and compress Figure 8: Vertical Louvers OptionalPush in spring to remove6.1 Changing Vent and Air Intake Orientation 6.3 Vent InstallationSECTION 6 VENTING 6.2 Venting6.5 Horizontal Venting 6.3.1Standard Vented Heaters Models UHAX 30 -6.4 Unvented Operation 6.7.1 Maximum Vent Lengths 6.6 Vertical Venting6.7 Length Requirements 6.8 Vent MaterialHorizontal Figure 9: Vent and Roof DetailVertical OptionPage Horizontal Figure 13: Concentric Vent BoxVertical Option OptionVent Terminal SECTION 7 AIR SUPPLY 7.1 Separated Combustion Installation7.2 Unvented Installation 7.3 Building VentilationFigure 15: Gas Connection SECTION 8: GAS PIPING8.1 Connections 9.1.1 Fan Control SECTION 9: WIRING9.1 Positioning Thermostats 9.2 Low Voltage Thermostat with One HeaterRelay Part Number ModelRelay Type UHAXS 30 -90436300 UHAXS 60 -DPST Max. Number of Heaters9.5 Internal Wiring Diagram 9.6 Ladder Wiring Diagram 9.7 Electrical Connection to the Heater 10.1.1 Louvers SECTION 10: OPERATION AND MAINTENANCE10.1 Pre-Start-UpChecks 10.1.2 Electrical ChecksRequired Incoming Signals Figure 16: Automatic Burner Control SequenceFigure 17: Gas Valve for Models UHAXS 30 - Signals Output By ControlCheck Gas Rate 10.2.3 Pressure SwitchFigure 18: Gas Valve for Models UHAXS 60 - 10.2.4 Turning Off the Heater10.3.1 Instruction to the User 10.2.5 External Controls10.3 Complete Start-Up SECTION 11: USER INSTRUCTIONS Reset Limit Switch - See Page 33, SectionFigure 19: Manual Reset Limit Switch 11.1 User InstructionsFigure 20: LED Diagnostic Codes 11.5 Simple Troubleshooting11.5.1 Simple Troubleshooting Burner Faults 11.4.2 To Turn the Heater Off12.4 Heat Exchanger Maintenance 12.2 Burner Maintenance12.3 Fan/Motor Assembly Maintenance 12.5 Gas Valve MaintenanceThe Vicinity of the Heater 12.8 Maintenance Checklist12.7 Venting and Air Intake Pipe See Page 6, SectionPipe when installedCombustion Air Intake Heat ExchangerSECTION 13: TROUBLESHOOTING 13.1 General STARTSECTION 13: TROUBLESHOOTING 13.3 Troubleshooting for Flame Supervision System Correct power 13.4Troubleshooting for Gas Valves13.5Troubleshooting for Flue Blower START14.1 Gas Valve SECTION 14 REPLACEMENT PARTSBurner Components 14.2 Burner Compartment 14.2.1 Burner Injectors14.3 Ignition Electrode and Flame Probe Install Vertical screws 14.4 Heat Exchanger14.5 Louver and Louver Springs Horizontal14.6 Flue Blower Vertical Installation 14.8 Ignition Control 14.7 Pressure Switch14.9 Axial Fan/Guard/Motor Assembly 14.10 Limit Switches 14.9.1 Fan Removal and Replacement14.9.2 To Replace the Fan Assembly 14.10.1 Removal and ReplacementSIDE VIEW SECTION 15: SPECIFICATIONS 15.1 Dimension DataTOP VIEW REAR VIEW15.2 General Technical Data Table All Models 15.3 Technical Data Table All ModelsROBERTS GORDON WILL NOT PAY FOR WARRANTY IS VOID IFROBERTS GORDON WILL PAY FOR Roberts-GordonPage Purchased From if different than installer OWNER WARRANTY REGISTRATION CARDAbout the Installer Type of Installation check onePage Page close to heater Installation ClearancesFire Hazard injury or property damage