Roberts Gorden BH15UT, BH35UT/EF, BH30UT/EF Grille End Cap Installation, Grille Installation

Page 51

SECTION 10: OPTIONAL HEATER ACCESSORIES

10.4Protective Grille Installation Step 10.4.1 Silicone Cap Installation

	Silicone Cap
Grille
Finger	Description	Part Number
	Grille Section	08050001
	Grille End Cap	08050002
	Silicone Cap	91915951-6P

Step 10.4.2 Grille End Cap Installation

Grille	Grille End Cap	A	B
			Bend up 90°.
Pull outward.		C	D

Step 10.4.3 Grille Installation

Reflector

1010 mm

Final Grille

Section

Grille

Grille

End Cap

45 of 75

Image 51

Contents Owner If you smell gasPage Roberts-Gordon LLC Table of ContentsPage Linear & Double Linear, One Side Reflector Table of FiguresPage Product Approval Heater Safety Manpower RequirementsSafety Labels and Their Placement Top Panel Label Placement Installer Responsibility Low Level User InstructionsNational Standards and Applicable Codes Clearances to Combustibles BH20ST BH40DL BH40ST/EFBH45ST/EF BH15ST BH30DLBH35ST/EF BH70DL/EF BH55STClearance Data -U Tube BH15UTBH20UT 250 1780 1960 560 200 1370 1500 560200 1530 1650 560 250 1630 1860 560Major Component Descriptions General Suspension Details Typical Suspension Details Linear & Double Linear Heater Installation Linear Standard Parts ListDescription Clips Weld SpotBurner Tube BH45ST/EFBH50ST/EF f BH55ST f BH15ST fBH20ST f BH35ST/EF fDouble Linear Standard Parts List Burner Tube Reflector Support Tube and Reflector Clips Assembly CouplingRepeated SideReflector Overlap approx Closed Burner Tube InstallationCoupling and Tube Assembly Open1 Coupling and Tube Assembly 2 Coupling and Tube AssemblyTighten slide bar as shown below Tube Clamp Package Installation 02750303 Option a Option BFan Tube Fan Tube Weld Spot Coupling TeeTube Standard Parts List Tube Heater Installation94320812 200 mm Tube Assembly OverviewBH35UT/EF g Reflector Overlap 1780 mm690 mm Burner Tube and Fan Tube Installation U-Tube Hanger PlacementNut Torque 13.56 Nm Lock Washer Tube Clamp 1 Tube Clamp Package InstallationU-Tube Support Bracket Assembly Installation BoltOrient coupling so that Impact block is Tube Installation U-Tube InstallationTube Support Bracket Assembly Coupling Reflector 02750303 Reflector Support Strap 03050000 Screw #8 x 3/4 3.9 x 19mm Multiburner Configuration & Installation Fan Tube Weld Spot Install Fully open positionDamper Flange ID/ID Sleeve Mm Hanger Reducer Typical Fan Arrangement Mm Hanger CrossMm Manifold Damper Typical Cross Mm Manifold Max 1000 3000 mm TeeBurner & FAN Installation Burner InstallationFan Assembly Tee Tighten securely until tube Cannot be removed Double Linear Fan InstallationTighten securely until tube Cannot be removedNon-Return Valve 1 Double Linear Fan InstallationUse 1 x ¾ reducer Not suppliedCondensate Drain Assembly Optional Heater Accessories 2 Side Reflector Installation Per reflector Use additional supports High air movementShe et Met al Screw Tube Cover Installation StepUse six #8 sheet metal screws to attach the joint piece 2 Frame Shield Installation Decorative Grille Installation .3.1 Grille Installation3 Grille Installation 2 Grille End Cap Installation3 Mesh Guard Connection Sports Hall Guard Installation2 Fastener Installation 1 Grille InstallationUndershield Installation 10.6.1 Hanger Installation Undershield InstallationAdjust Undershield Height Wall Mounting Hardware InstallationLinear Venting Outside Combustion Air Supply Air Supply RequirementsEnd of Tube Fan Tube Common Duct Fresh Air Intake SpigotGAS Piping Connector 545 mm Minimum Burner Shut-Off Valve Supplied by Roberts-Gordon 1000 mm LongGas Supply Pipe Wiring Typical External Wiring Diagram Linear or U-TubeTypical External Wiring Diagram Double Linear Option Typical External Wiring Diagram Multiburner Internal Wiring Diagram Heater Lockout Indication Optional Operation and serviceOperation Tubing may still be hotCommissioning Multiburner Heater Lockout Indicator by ConnectorHeater Lockout Indicator by Volt Free Connector TestingECA Approved Systems Multiburner only Servicing Instructions Vehicles and Other Objects Pressure SwitchAutomatic Flame Control Unit NeonsWindow TubesGas Line Burner ObservationTroubleshooting U-Tube Troubleshooting Flow Chart Linear, Double LinearTroubleshoot Ends Troubleshooting Flow Chart Linear, Double Linear and U-TubeTroubleshooting Flow Chart Multiburner Re-establish continuity Purge Lines Troubleshooting Flow Chart MultiburnerManifold Gas Pressure Setting Governor orifice pressureWhile burner is running. See Replacement Parts Item Description Specifications Linear Heater Double Linear HeaterTube Heater Burner Airplate ID Number Jet Numbers #30 #19 Natural G20 Burner SpecificationsStandard BH15 BH20 BH25 BH30 BH35 BH40 BH45 BH50 BH55BH25/EF BH30/EF BH35/EF BH40/EF BH45/EF BH50/EF EF Burner SpecificationsPage Page F r a r e d H e a t i n g