York HFC-410A manual Drawing, Side Supply / Rear Return

Page 33

JOHNSONCONTROLS	FIG.4–GENERAL	NOTES:
JOHNSONCONTROLS	FIG.4–GENERAL	1. 10’ Clearance Minimal Over The Top of the Condensing Unit.
		2. Only One Adjacent Wall Can Exceed Unit Height.
		3. 12’ Clearance Required to Adjacent Units
		4. 8’ Service AccessRecommended on One Side.
	ARRANGEMENT	5. Economizer and Exhaust Hoods, Where Applicable, are Folded Inside Unit for Shipment.
	ARRANGEMENT	339.00	OA
		170.31
		ELECTRICAL SERVICE
	DRAWING	TOP VIEW	OA
			OA

120.00 CLEAR

SECTION DESCRIPTIONS:

EE= Economizer FE = Fan Exhaust _F = Filter Segments CC = Cooling Coils FS = Supply Fan

DP = Discharge Plenum CO = Condenser Section

SIDE SUPPLY / REAR RETURN

82.00

	92.00
	100.50
30.00 DOOR
SWING	FRONT VIEW
CLEARANCE
BOTH SIDES
78.00 CLEAR
FOR COIL PULL

91.00
CLEAR	84.00
FOR COIL	CLEAR
PULL

	FS	CC			EE
CO	DP		_F		EE
			_F
66.00
					FE
11.00
		1.50	1-1/4" FPT
			DRAINS
			BOTH SIDES
	39.00		60.00	106.00	46.00
			195.00
		227.25

SIDE VIEW (LEFT SIDE)

	36.28
	6.36
7.76	76.48
	136.82

REAR VIEW

60.00 CLEAR

FOR AIR INTAKE

BOTH SIDES

AIRFLOW

33

LD08296

FORM 100.50-EG5 (108)

Image 33

Contents 90.1 AshraeCompliant MEA 231-02-EIntroduction Indoor air quality features for the indoor environ- mentLower total cost of ownership Simplicity Elite controller OptionTable of Contents Features and Beneﬁts Filter Options CommunicationsOutside AIR Damper Options Relief SystemCabinet Features and Options Condenser Features and OptionsEvaporator Section Roof CurbsAccessories Application Data Unit PlacementGeneral LocationUnit Orientation Duct ConsiderationsHorizontal Applications EconomizerHarsh Environments Condenser and Evaporator Coil Protection VAV Supply AIR Pressure ControlCopper-Fin Evaporator and Condenser Coil Building Pressure Control SystemsAcoustical Considerations This page intentionally left blank York NomenclaturePhysical Data Physical Data050 051 060 061 Gas Furnaces ModelMinimum OA Temp for Mech. Cig Low Ambient Option Min. OA Temp Minimum Airﬂow HeatingIplv Ieer ModelEER Model Supply Blower Cooling Only Gas Heat TypeAir Altitude feet Temp Altitude and Temperature CorrectionsALTITUDE/TEMPERATURE Conversion Factor Cooling Performance DATA* 50 TON Standard Capacity Cooling Performance Data 050 ModelCooling Performance DATA* 55 TON High Capacity Cooling Performance Data 051 ModelCooling Performance DATA* 60 TON Standard Capacity Cooling Performance Data 060 ModelCooling Performance DATA* 65 TON High Capacity Cooling Performance Data 061 ModelSupply Fan Data Total Static Pressure inches of water columnCFM STD. AIR BHP RPM CFM Component Static Pressure DropsExhaust FAN Motor Sizing Instructions Exhaust Fan DataCFM STD AIR BHP RPMElectrical Data Electrical Service SizingLoad Deﬁnitions RLA LRAUnit Size Quantity FLAFans AmpsControls Unoccupied / Occupied SwitchingGAS Heating Operation Morning WARM-UPEconomizer Operation Ventilation Control SequencesExhaust Control Sequences LOW-AMBIENT/HEAD-PRESSURE Control Operation Smoke Purge SequenceSupply FAN Operation Cooling OperationHeating Operation POWER-SUPPLY-CONDUCTOR Size RangeDual-Point TB Supply Single-PointGeneral Arrangement Drawing General ArrangementSide Supply / Rear Return DrawingTOP View DrawingsGeneral Arrangement Drawing Curb Layout DrawingUnit Weights Unit Corner Weights Guide Speciﬁcations Equipment WarrantiesProduct Speciﬁcation Unit ConstructionEvaporator Section Filter SectionSupply Fan Section Discharge PlenumCondenser Section Controls Simplicity Elite Installation ExecutionInspection and START-UP Supervision ALL Rights Reserved