United States Stove 6035 owner manual Safety Steps, Burning Solid Fuels, Ussc

Page 3
SAFETY STEPS

SAFETY STEPS

IMPORTANT: Proper installation of this stove is necessary for safe and efficient operation. Installing this product improperly may result in a house fire and personal injury. All applicable building codes for your location must be followed. In areas where building codes require additional steps to the installation of this product not included in this manual the building codes will take precedent and must be followed. Contact your local building inspector to obtain any necessary permits or inspection guidelines before installing the product.

The American Harvest stove is designed to burn shelled corn, cherry pits, or pelletized fuel such as wood pellets. The burning of other solid fuels such as cord wood or wood chips in this stove is not permitted.

This product requires simple periodic maintenance for proper operation and long life of the stove. Read and follow the maintenance schedule closely.

DISCONNECT THE POWER CORD BEFORE SERVICING THIS STOVE! A power surge protec- tor is required. The unit must be plugged in to a grounded 110-volt power source.

Always route the power cord away from the unit. Do not route cord in foot traffic areas. Do not pinch cord under furniture.

A working smoke detector must be installed in the same room as this product.

Flammable or explosive liquids such as gasoline, naphtha or engine oil must NEVER be used in or around this stove. These liquids must be stored well away from this stove as the open flame in the burner chamber could ignite the fumes of such liquids. Do not burn garbage in this unit.

The moving parts of this stove are propelled by high torque electric motors. The auger and Fuel Agitator can cause severe injury to body parts that may get near them. Keep all body parts away from the auger and Fuel Agitator while the stove is plugged into an electrical outlet. These moving parts may begin to move at any time while the stove is plugged in.

According to HUD requirements, when installed in a mobile home, this stove must be grounded directly to the steel chassis of the mobile home and bolted to the floor. Direct air access must be provided - Use 60FAK Fresh Air Kit

This stove is not intended for use in commercial installations.

Do not connect this stove to “B” vent. Use UL Listed Pell Vent ONLY!

BURNING SOLID FUELS

Ashes will have to be Removed from the stove periodically. See cleaning procedure. You can minimize cleaning required and maximize efficiency by maintaining the correct draft settings. See “Draft Setting” further in the manual.

The draft setting on your stove may have to be changed from time to time to accommodate your specific burning conditions. Proper draft setting will be discussed later in this manual. The point we wish to make here is that your American Harvest stove, due to the nature of solid fuels, will require brief periodic attention. Please do not expect to light your stove and walk away from it until you want to shut if off in the spring. A few moments of adjustment and cleaning from time to time is an important part of burning solid fuels, due to the vast differences in fuel, humidity and outside temperature.

The American Harvest stove has been designed to burn dry shelled corn, wood pellets and other pelletized fuels that meet Association of Pellet Fuel Industries standards.

USSC

3

Image 3
Contents SAVE THESE INSTRUCTIONS CORN & PELLET MULTIFUEL STOVE6035 K e e p i n g North America Warm SinceCONGRATULATIONS SPECIFICATIONSNOTE YOUR UNIT MUST BE INSTALLED BY A QUALIFIED HEATER INSTALLERSAFETY STEPS BURNING SOLID FUELSUSSC WOOD PELLETS BURNING SOLID FUELS continuedParallel / Alcove Installation INSTALLATION REQUIREMENTSCLEARANCES TO COMBUSTIBLES FLOOR PROTECTIONCLEARANCES TO COMBUSTIBLES continued GUIDELINES FOR EXHAUST VENTING SYSTEMS DESIGNHEARTH PROTECTION USSC 90 DEGREE BEND TERMINATION WIND HOOD TERMINATIONWind Hood 3” Min. Diameter ROOF MUST BE MAINTAINED INSTALLATION CONFIGURATIONSMOBILE HOME INSTALLATION REQUIREMENTS DO NOT INSTALL IN SLEEPING ROOMALCOVE CLEARANCE RECOMMENDATIONS ALCOVE INSTALLATION REQUIREMENTSALCOVE-THROUGHTHE WALL INSTALLATION REQUIREMENTS Corner InstallationHorizontal Exhaust Termination FREESTANDING STOVE INSTALLATION REQUIREMENTSINSIDE VERTICAL PIPE WITH ROOF TERMINATION THROUGH THE ROOF Do not use abrasive cleaners GLASS MAINTENANCE, REMOVAL AND REPLACEMENTCLEANING THE GLASS REMOVAL OF BROKEN OR DAMAGED CERAMIC GLASSFront View Circuit Board Control Panel STOVE CONTROLSAdjustable Door Handle Service NoteDamper Control Function LIGHTING INSTRUCTIONSShutdown DISPOSAL OF ASHESCIRCUIT BOARD FUNCTIONS Start-upSoot and Flyash - Formation and Need for Removal SETTING THE DRAFTMAINTENANCE INSTRUCTIONS Daily MaintenanceSPECIALCLEANING/OPERATIONALINSTRUCTIONS Maintenance Instructions ContinuedWeekly Maintenance SPRING CLEANINGPressure Switch AUTOMATIC SAFETY FEATURESHOPPER AUGER SAFETY SWITCH LOCATION Micro SwitchTHERMOSTAT INSTALLATION FUEL ADDITIVEBack of Circuit Board CAUSES TROUBLE SHOOTINGPROBLEM SOLUTIONSCAUSES TROUBLE SHOOTING continuedPROBLEM SOLUTIONSCAUSES TROUBLE SHOOTING continuedPROBLEM SOLUTIONSUSSC WIRING DIAGRAMUSSC REPAIR PARTS DIAGRAM-6035REPAIR PARTS LIST-6035 PART #DESCRIPTION HOW TO ORDER REPAIR PARTS