Teka TR 640, TT 620, VT CM, VT DUAL., 1 VTC B, TB 600, TR 735 AB manual Fixing the hob See figs, Models

Page 15

 

 

 

fig. 2

Fitting holes

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

7

 

 

 

 

 

 

5

 

 

 

 

 

 

n

 

 

 

 

 

u

 

 

 

 

 

im

 

 

 

 

 

x

 

 

 

 

 

a

 

 

 

 

 

 

m

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

7

 

 

 

 

 

5

 

 

 

 

 

n

 

 

 

 

 

u

 

 

 

 

 

im

 

 

 

 

 

x

 

 

 

 

 

a

 

 

 

 

 

 

m

 

 

 

 

 

 

 

L

W

 

VTN DC and TC 620

Rest of the models The dimensions L and W are shown in the table "Dimensions and characteris- tics" of the Technical Information section.

space of at least 20 mm should be left at the back of the cupboard. As an alternati- ve to this type of panel, you can install a detachable protective cover to the bottom of the hob, which can be obtained from our Technical Services using the reference in- dicated.

Protective cover

Ref.

Models

81253177

TT 600, TB 600, TR 640, TT

640, TR 620, TT 630, TR 600,

 

TR 735 AB, TM 620, TR 641

 

and TM 601

 

 

81253176

VT TC 60.3, TT 620 and

TC 620

 

When hobs are handled before being installed, care should be taken in case there is any protruding part or sharp edge which could cause injury.

When installing units or applian- ces above the hob, the hob should be

GB

protected by a board so that the glass cannot be damaged by accidental blows or heavy weights.

The glues used in manufacturing the kitchen unit and in the adhesive on the decorative laminate of the worktop surface should be made to tolerate tem- peratures of up to 100ºC.

TEKA assumes no responsibility for any malfunction or damage caused by faulty installation.

PLEASE REMEMBER THAT THE GUA- RANTEE DOES NOT COVER THE GLASS IF IT SUFFERS A VIOLENT BLOW OR IF IT IS USED IMPROPERLY.

Fixing the hob

(see figs. 3 and 4)

When the gap has been properly sized, the sealing washer should be put on the lower part of the hob. With models VR 622, TR 620, TR 640, TT 640, TT 600, TB 600, TR 600, TT 630, TR 735 AB, TM 620, TR 641 and TM 601 the washer will be stuck to the lower face of the glass.

Silicone should not be applied between the glass and the unit worktop because if it becomes necessary to remove the hob from its position, the glass could break when trying to detach it.

Position the clips as shown in the diagram, fastening them to the openings in the lower part of the body using the screws provided.

For worktop thicknesses of 30 mm. or less, use the self-tapping screws (M5) that are provided as a fastening accessory - put them into the clip’s round hole. This hole will be threaded as the screw is inserted into it, and this should be done before fi- xing the clip to the worktop.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents
Ceramic Hobs Contents / Inhalt / Table des Matières / Spis treœci Utilisation ET Entretien InstallationPrésentation Informations TechniquesGB Model VT CM Model VTN DCModell VTN DC Modèle VTN DCModel VT CM Inox Halogen GB Model VT DUAL.1DE Modell VT DUAL.1 FR Modèle VT DUAL.1Model VTC B Model VTC DCModell VTC DC Modèle VTC DCModel TT Model VRModell VR Modèle VRModell TR Model VT TC Model TRModell VT TC Modèle VT TCGB Models TR 640 and TT GB Model TTDE Modelle TT FR Modèle TTModelle TC Model TT 600, TR 600 and TB Model TCModell TT 600, TR 600 und TB Modèle TT 600, TR 600 et TBModèle TM Model TR 735 AB Model TMModell TR 735 AB Modell TM Modèle TR 735 AB Model TM Model TR Modell TM Modell TR Modèle TM Modèle TR Safety instructions Guide to Using the Instructions BookletPositioning the hobs GB InstallationModels Fixing the hob See figsJoining the hob to the oven Or the control panel Connecting the electricityCeramic hobs with controls Positioning the ovenConnecting the gas Model VT DUAL.1Rear view of the Control Panel Gas conversion Electrics Hob dimensionsConfiguration UnitGas Characteristics Common to ALL Models Characteristics of the VT DUAL.1Technical details Touch control user Instructions Special requirements Before first useSwitching the Appliance on Selecting the Hotplate to be Switched onModels TR 640, TT 640, TR 620, TT 620 and TM Connecting / Turning on the Double and Triple Hotplate Switching the Hotplate OFFResidual Heat Indicator Switching the Appliance OFFUnlocking for cooking only models shown in figure Disconnecting / Turning OFF the Double HotplateLocking the Hobs Sensors Models TT 630, TC 620 and TRHeat-up function Automatic cooking start Safety disconnectionCancelling the locking function Switching HEAT-UP Function onSwitching on the clock Timer FunctionModifying the Power Level DU- Ring HEAT-UP Function Switching HEAT-UP Function OFFModels TC 620, TR 735 AB and TR Disconnecting the clockQuick switch-off Viewing / Changing the programmed timeModels TT 640 and TR Clock as a Countdown timerSwitching on the counter Changing the programmed timeSwitching off the counter Power surgesDouble Circuit Instructions Ceramic hobs with controls InstructionsResidual Heat Indicators Anti-accidental turn system On gas controlsIgniting the burners Suggestions for using the burners effectively Advice on using the hotplates effectively Cleaning and care the burnersMantaining the VT DUAL.1 Light soiling Cleaning and careCleaning and Care the Glass Recommended Cleaning ProductsCleaning and Care the Frame When the glass’ colour changesMessage ER 21 on the control and subsequent disconnection Message ER 25 and the beeping signalNeither the hotplates nor the pilot lights are working Pan is sticking to the glassGas burners are making the pans dirty Gas burners are not lightingTeka Industrial, S.A Teka Küchentechnik GmbH Teka Group
Related manuals
Manual 38 pages 12.62 Kb
Top Page Image Contents