Gas conversion

Teka TT 640, TT 620, VT CM, VT DUAL., 1 VTC B, TB 600, TR 640, TR 735 AB, TR 600, TT 600 Gas conversion

Page 18

pipe, a maximum torque of 300 Kgf * cm should be applied.

When the gas connection has been made, the installation should be checked to ensu- re that it is completely sealed. If the check is done using air, care should be taken that the test pressure is no more than 200 g./cm2. Where air is not available, soapy water should be applied to ensure that there are no leaks in the connections. Tes- ting should never be done using a flame.

When the hob has been installed, check that the burner minimums are properly ad- justed. To do this, light the burners and check that they do not go out if you switch quickly from the maximum to the minimum.

Important!

Any alteration that is to be made to the appliance to convert it to a different type of gas should only be carried out by a qualified technician.

Information for Technical Assis- tance: whenever the type of gas or the ap- pliance’s pressure is changed, the new re- gulation plate should be placed on top of the old one so that the new features can be seen after the change.

The tasks involved in conversion are:

*Replace the injectors.

*Adjust the taps’ minimums.

The injectors required for each gas type are shown in table 1.

To replace the injectors, follow these ins- tructions:

1Remove the grids and upper parts of the burner so that the injector can be seen.

2Using a number 7 pipe spanner, remove the injectors and replace them with the new ones. Take care to press the injector down firmly so that there is no leakage.

3Replace the grid and burners that were previously removed.

When the injectors have been changed, this is how to adjust the minimums:

1Take the oven or the control panel out so that you can access the gas taps.

2Turn the burners on to their minimum.

3Use a slim, grooved screwdriver to turn the screw located to the right or in the centre of the gas tap’s shaft (the flame increases when you turn to the left and decreases when you turn to the right).

4When properly adjusted, check that the flame does not go out when you turn the knob quickly from maximum to minimum.

TEKA INDUSTRIAL, S.A. assumes no responsibility for any hob malfunction if the gas conversion or the adjustment of the burners’ minimums has not been carried out by TEKA’s official personnel.

Table 1

Burner		Family
	Second		Third
	Group H	Group E+	Group 3+
Rapid	116 Y	116 Y	85

Semi-rapid	97 Z	97 Z	66

Ø injector expressed in 1/100 mm.

Image 18

Contents

Ceramic Hobs Contents / Inhalt / Table des Matières / Spis treœci Informations Techniques InstallationPrésentation Utilisation ET EntretienModèle VTN DC Model VTN DCModell VTN DC GB Model VT CMFR Modèle VT DUAL.1 GB Model VT DUAL.1DE Modell VT DUAL.1 Model VT CM Inox HalogenModèle VTC DC Model VTC DCModell VTC DC Model VTC BModèle VR Model VRModell VR Model TTModèle VT TC Model VT TC Model TRModell VT TC Modell TRFR Modèle TT GB Model TTDE Modelle TT GB Models TR 640 and TTModèle TT 600, TR 600 et TB Model TT 600, TR 600 and TB Model TCModell TT 600, TR 600 und TB Modelle TCModèle TR 735 AB Model TR 735 AB Model TMModell TR 735 AB Modell TM Modèle TMModel TM Model TR Modell TM Modell TRModèle TM Modèle TR Guide to Using the Instructions Booklet Safety instructionsGB Installation Positioning the hobs Fixing the hob See figs ModelsPositioning the oven Connecting the electricityCeramic hobs with controls Joining the hob to the oven Or the control panelConnecting the gas Model VT DUAL.1Rear view of the Control Panel Gas conversion Unit Hob dimensionsConfiguration ElectricsGas Characteristics Common to ALL Models Characteristics of the VT DUAL.1Technical details Special requirements Before first use Touch control user InstructionsSwitching the Appliance on Selecting the Hotplate to be Switched onModels TR 640, TT 640, TR 620, TT 620 and TM Switching the Appliance OFF Switching the Hotplate OFFResidual Heat Indicator Connecting / Turning on the Double and Triple HotplateModels TT 630, TC 620 and TR Disconnecting / Turning OFF the Double HotplateLocking the Hobs Sensors Unlocking for cooking only models shown in figureSwitching HEAT-UP Function on Safety disconnectionCancelling the locking function Heat-up function Automatic cooking startSwitching HEAT-UP Function OFF Timer FunctionModifying the Power Level DU- Ring HEAT-UP Function Switching on the clockViewing / Changing the programmed time Disconnecting the clockQuick switch-off Models TC 620, TR 735 AB and TRChanging the programmed time Clock as a Countdown timerSwitching on the counter Models TT 640 and TRPower surges Switching off the counterCeramic hobs with controls Instructions Double Circuit InstructionsResidual Heat Indicators Anti-accidental turn system On gas controlsIgniting the burners Suggestions for using the burners effectively Advice on using the hotplates effectively Cleaning and care the burnersMantaining the VT DUAL.1 Recommended Cleaning Products Cleaning and careCleaning and Care the Glass Light soilingWhen the glass’ colour changes Cleaning and Care the FramePan is sticking to the glass Message ER 25 and the beeping signalNeither the hotplates nor the pilot lights are working Message ER 21 on the control and subsequent disconnectionGas burners are not lighting Gas burners are making the pans dirtyTeka Group Teka Industrial, S.A Teka Küchentechnik GmbH

Related manuals

Teka TT 640, TT 620, VT CM, VT DUAL., 1 VTC B, TB 600, TR 640, TR 735 AB, TR 600, TT 600 Gas conversion

Gas conversion