Viewing / Changing the programmed time

Teka TT 640 Viewing / Changing the programmed time, Disconnecting the clock, Quick switch-off

Page 28

To view on the clock indicator (8) the time left before the hotplate turns off, you only have to select the hotplate required, both the decimal point (13) and the control pilot light (11) which corresponds to the selec- ted hotplate will turn on.

If you wish to change the time left, follow the steps below:

1 The hotplate that is to be controlled must have already been selected. Both the decimal point (13) and the control pilot

(11)which corresponds to the selected hotplate must be on.

2 Touch the clock sensor (7). The deci- mal point (13) for the clock will come on.

3 Use the or sensors (5/4) to alter the time.

Alternatively you can directly touch the clock sensor (7) various times until the control pilot (11) for the hotplate required comes on. You can then also change the time, if required, using the sensors or (5/4).

Disconnecting the clock

When the time that was programmed for the hotplate elapses, a series of beeps will sound for at least a minute.

To stop the beeping, touch any sensor. The hotplate will now be disconnected.

If you wish to stop the clock before the time programmed has elapsed:

1 The hotplate that is to be controlled must have already been selected. The deci- mal point (13) and the pilot light for the

selected hotplate (11) must be on.

2 Touch the clock sensor (7). The deci- mal point for the clock (13) will come on.

3 Use the sensor (4) to decrease the time to 00.

Quick switch-off

Repeat steps 1 and 2 above.

3 Touch sensors and (5 and 4) si- multaneously and the clock will be dis- connected.

The clock will have been cancelled, but the hotplate will still be active until you switch it off.

MODELS TC 620, TR 735 AB AND TR 641

On these models, you can use the clock as a countdown timer for periods between 1 and 99 minutes, and as a hotplate timer for times between 1 and 99 minutes. All the cooking areas can be programmed inde- pendently and simultaneously.

Timing a hotplate

1 The cooking area to be timed has to be selected. The corresponding decimal point (13) must be lit.

2 Select a power level of between 1 and 9 using the or sensors (5-4).

3 Touch the clock sensor (7). The deci- mal point (13) of the time display (8) (which shows 00) will come on, and it will flash on and off along with the con- trol display (11) of the corresponding area.

4 Touch the clock sensor (7) again to increase the value of the time you wish

Image 28

Contents

Ceramic Hobs Contents / Inhalt / Table des Matières / Spis treœci Installation PrésentationInformations Techniques Utilisation ET EntretienModel VTN DC Modell VTN DCModèle VTN DC GB Model VT CMGB Model VT DUAL.1 DE Modell VT DUAL.1FR Modèle VT DUAL.1 Model VT CM Inox HalogenModel VTC DC Modell VTC DCModèle VTC DC Model VTC BModel VR Modell VRModèle VR Model TTModel VT TC Model TR Modell VT TCModèle VT TC Modell TRGB Model TT DE Modelle TTFR Modèle TT GB Models TR 640 and TTModel TT 600, TR 600 and TB Model TC Modell TT 600, TR 600 und TBModèle TT 600, TR 600 et TB Modelle TCModel TR 735 AB Model TM Modell TR 735 AB Modell TMModèle TR 735 AB Modèle TMModell TM Modell TR Model TM Model TRModèle TM Modèle TR Guide to Using the Instructions Booklet Safety instructionsGB Installation Positioning the hobsFixing the hob See figs ModelsConnecting the electricity Ceramic hobs with controlsPositioning the oven Joining the hob to the oven Or the control panelModel VT DUAL.1 Connecting the gasRear view of the Control Panel Gas conversion Hob dimensions ConfigurationUnit ElectricsGas Characteristics of the VT DUAL.1 Characteristics Common to ALL ModelsTechnical details Special requirements Before first use Touch control user InstructionsSelecting the Hotplate to be Switched on Switching the Appliance onModels TR 640, TT 640, TR 620, TT 620 and TM Switching the Hotplate OFF Residual Heat IndicatorSwitching the Appliance OFF Connecting / Turning on the Double and Triple Hotplate Disconnecting / Turning OFF the Double Hotplate Locking the Hobs Sensors Models TT 630, TC 620 and TR Unlocking for cooking only models shown in figureSafety disconnection Cancelling the locking functionSwitching HEAT-UP Function on Heat-up function Automatic cooking startTimer Function Modifying the Power Level DU- Ring HEAT-UP FunctionSwitching HEAT-UP Function OFF Switching on the clockDisconnecting the clock Quick switch-offViewing / Changing the programmed time Models TC 620, TR 735 AB and TRClock as a Countdown timer Switching on the counterChanging the programmed time Models TT 640 and TRPower surges Switching off the counterCeramic hobs with controls Instructions Double Circuit InstructionsAnti-accidental turn system On gas controls Residual Heat IndicatorsIgniting the burners Suggestions for using the burners effectively Cleaning and care the burners Advice on using the hotplates effectivelyMantaining the VT DUAL.1 Cleaning and care Cleaning and Care the GlassRecommended Cleaning Products Light soilingWhen the glass’ colour changes Cleaning and Care the FrameMessage ER 25 and the beeping signal Neither the hotplates nor the pilot lights are workingPan is sticking to the glass Message ER 21 on the control and subsequent disconnectionGas burners are not lighting Gas burners are making the pans dirtyTeka Group Teka Industrial, S.A Teka Küchentechnik GmbH

Related manuals

Teka TT 640 Viewing / Changing the programmed time, Disconnecting the clock, Quick switch-off