Teka TR 640, TT 620, VT CM, VT DUAL., 1 VTC B Locking the Hobs Sensors, Models TT 630, TC 620 and TR

Page 25

4 On model TR 735 AB, if once the second circuit is in operation you then wish to activate the third circuit, touch the sen- sor (6) once again. Once you have done this, the second pilot light (10) will come on.

Models TT 630, TC 620 and TR 641:

The double circuit may be activated or de- activated by touching the sensor (6) at any time, providing the hotplate is swit- ched on.

DISCONNECTING / TURNING OFF THE DOUBLE HOTPLATE

1 The hotplate that you want to disconnect has to be already activated. The decimal point (13) must be lit.

2 Touch the double hotplate's sensor

(6). The pilot (10) will go off, and the out- side ring will be disconnected.

DISCONNECTING / TURNING OFF THE TRIPLE HOTPLATE (MODEL TR735 AB)

1 Touch the sensor (6). The first pilot light (10) will go off, and the third ring will be disconnected.

2 If you touch the sensor (6) once again the second pilot light (10) will go off and the second ring will be disconnected. Only the first circuit will remain on.

Locking the Hob's Sensors

To avoid the controls being tampered with, you can block the entire unit, except for the on/off sensor, using the locking sensor (9), (except on models TT 600, TB 600,

TT630, TR 600, TC 620, TR 735 AB, TR 641 and TM 601 - see next section). This feature is useful as a child-safety device. When locking is enabled, the pilot light

GB

(12) is lit.

If you use the on / off sensor to turn the ap- pliance off when locking is activated, the appliance will still be locked when you turn the appliance back on again.

SAFETY FUNCTION (only models TT 600, TB 600, TR 600, TT 630, TC 620, TR 735 AB, TR 641 and TM 601 )

The safety function can be enabled after the hob is connected. To do so, touch sen- sor (1) to enable the touch control. Im- mediately touch sensor (4) for five se- conds. An L (for 'Locked') will appear on the displays. The touch control will be swit- ched off after a few seconds. If the cooking area is hot, an L and an H will appear al- ternately on the corresponding display.

This needs to be done within 5 seconds after the touch control is activated, with no sensor other than those indicated being touched during that time, or the locking will not be carried out.

The electronic control will remain locked until the user unlocks it, even after the con- trol is disconnected using the on/off sensor or when restarting after there has been a power cut.

Unlocking for cooking (only models shown in figure 8)

To unlock the control and use it, touch sen- sor (1) to enable the touch control. Im- mediately touch, at the same time, the two sensors to the right or, on models TR 735 AB and TT 630, to the left. The L va- nishes from the display and an 0 appears with the lower point flashing, or a H and an 0 appear alternately if the corresponding hotplate is hot, and the hob will be ready to use for cooking. When you disconnect the

control with the on/off sensor (1) the

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents
Ceramic Hobs Contents / Inhalt / Table des Matières / Spis treœci Présentation InstallationInformations Techniques Utilisation ET EntretienModell VTN DC Model VTN DCModèle VTN DC GB Model VT CMDE Modell VT DUAL.1 GB Model VT DUAL.1FR Modèle VT DUAL.1 Model VT CM Inox HalogenModell VTC DC Model VTC DCModèle VTC DC Model VTC BModell VR Model VRModèle VR Model TTModell VT TC Model VT TC Model TRModèle VT TC Modell TRDE Modelle TT GB Model TTFR Modèle TT GB Models TR 640 and TTModell TT 600, TR 600 und TB Model TT 600, TR 600 and TB Model TCModèle TT 600, TR 600 et TB Modelle TCModell TR 735 AB Modell TM Model TR 735 AB Model TMModèle TR 735 AB Modèle TMModell TM Modell TR Model TM Model TRModèle TM Modèle TR Safety instructions Guide to Using the Instructions BookletPositioning the hobs GB InstallationModels Fixing the hob See figsCeramic hobs with controls Connecting the electricityPositioning the oven Joining the hob to the oven Or the control panelModel VT DUAL.1 Connecting the gasRear view of the Control Panel Gas conversion Configuration Hob dimensionsUnit ElectricsGas Characteristics of the VT DUAL.1 Characteristics Common to ALL ModelsTechnical details Touch control user Instructions Special requirements Before first useSelecting the Hotplate to be Switched on Switching the Appliance onModels TR 640, TT 640, TR 620, TT 620 and TM Residual Heat Indicator Switching the Hotplate OFFSwitching the Appliance OFF Connecting / Turning on the Double and Triple HotplateLocking the Hobs Sensors Disconnecting / Turning OFF the Double HotplateModels TT 630, TC 620 and TR Unlocking for cooking only models shown in figureCancelling the locking function Safety disconnectionSwitching HEAT-UP Function on Heat-up function Automatic cooking startModifying the Power Level DU- Ring HEAT-UP Function Timer FunctionSwitching HEAT-UP Function OFF Switching on the clockQuick switch-off Disconnecting the clockViewing / Changing the programmed time Models TC 620, TR 735 AB and TRSwitching on the counter Clock as a Countdown timerChanging the programmed time Models TT 640 and TRSwitching off the counter Power surgesDouble Circuit Instructions Ceramic hobs with controls InstructionsAnti-accidental turn system On gas controls Residual Heat IndicatorsIgniting the burners Suggestions for using the burners effectively Cleaning and care the burners Advice on using the hotplates effectivelyMantaining the VT DUAL.1 Cleaning and Care the Glass Cleaning and careRecommended Cleaning Products Light soilingCleaning and Care the Frame When the glass’ colour changesNeither the hotplates nor the pilot lights are working Message ER 25 and the beeping signalPan is sticking to the glass Message ER 21 on the control and subsequent disconnectionGas burners are making the pans dirty Gas burners are not lightingTeka Industrial, S.A Teka Küchentechnik GmbH Teka Group
Related manuals
Manual 38 pages 12.62 Kb
Top Page Image Contents