Samsung AR07MSPXAWKNEU manual Optional Extending the power cable, Compression dimension should be

Page 11

WARNING

Connect the wires firmly so that wires cannot be pulled out easily. (If they are loose, it could cause burn-out of the wires.)

Step 2.4 Optional: Extending the power cable

1Prepare the following tools.

Tools

Spec

Shape

Crimping pliers

MH-14

 

Connection sleeve

20xØ7.0

 

(mm)(HxOD)

Insulation tape

Width 18

mm

 

 

 

Contraction tube

50xØ8.0

(mm)

(LxOD)

2As shown in the figure, peel off the shields from the rubber or wire of the power cable.

Peel off 20 mm of cable shields from the preinstalled tube.

CAUTION

For information about the power cable specifications for indoor and outdoor units, refer to the installation manual.

After peeling off cable wires from the preinstalled tube, insert a contraction tube.

Method 1

Method 2

 

 

 

 

 

 

 

Connection sleeve

Connection sleeve

4Using a compressor, compress the two points and flip it over and compress another two points in the same location.

• The compression dimension should be 8.0.

Compression dimension

After compressing it, pull both sides of the wire to make sure it is firmly pressed.

Method 1

Method 2

Compress it 4 times.

Compress it 4 times.

5 mm

5 mm

5Wrap it with the insulation tape twice or more and position your contraction tube in the middle of the insulation tape.

Three or more layers of insulation are required.

Power cable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20

 

20

 

 

 

20

 

 

 

 

60

 

 

Method 1 Insulation tape

40 mm

Method 2 Insulation tape

35 mm

 

120

180

(Unit: mm)

 

Pre-installed tube for the power cable

6Apply heat to the contraction tube to contract it.

Contraction tube

20

(Unit: mm)

3Insert both sides of core wire of the power cable into the connection sleeve.

Method 1: Push the core wire into the sleeve from both sides.

Method 2: Twist the wire cores together and push it into the sleeve.

7After tube contraction work is completed, wrap it with the insulation tape to finish.

Insulation tape

Installation

English 11

Image 11
Contents Air conditioner Contents General information Safety Information on InstallationFires, explosions or injuries Install the unit in a place where water can drain smoothlyCases Choosing the installation locationPreparation Minimum clearances for the outdoor unitUnit mm AccessoriesAccessories in the indoor unit package Thermometer Resistance meter Electroscope English Accessories in the outdoor unit packageTools General tools Tools for test operationTaping the pipes, cables, and drain hose Drilling a hole through the wallRemove the cap screws, then the screws Indoor Unit InstallationInstallation plate Disassembling the cover panelConnecting the Power and communication cables assembly cable Compression dimension should be Optional Extending the power cableFire Installing and connecting the drain hoseInstall the drain hose Optional Extending the drain hoseOptional Changing the direction of the drain hose Pass the pipe through the hole in the wall Shortening or extending the refrigerant pipes assembly pipeWhen fixing the indoor unit on a window frame 10 Fixing the installation plateWhen fixing the indoor unit on a wall 12 Assembling the cover panel 11 Fixing the indoor unit to the installation plateWhen fixing the indoor unit on a gypsum board Fix the installation plate without inclining to one sideThat the fan can operate correctly Outdoor Unit InstallationFixing the outdoor unit in place Refrigerant pipesCooling capacity and malfunction. Use a vacuum pump Leave the system in the standby modeEvacuating the air Siphon Adding refrigerant①+②, c Running the Smart Install mode Installation InspectionBlocking error Open Error betweenPower cable or communication Motor Connector Remove foreign substance. CheckLet the compressor run for more than 5 minutes Check the following Strength of the installation sitePerforming final check and trial operation Pumping down for removing the productAssemble the Case Sub PCB to the indoor unit Sub PCB installationoptionalAttach the Sub PCB to the Case Sub PCB DB68-06732A-03
Related manuals
Manual 2 pages 25.92 Kb Manual 39 pages 32.94 Kb Manual 25 pages 2.73 Kb Manual 36 pages 62.01 Kb Manual 36 pages 15.94 Kb Manual 36 pages 60.74 Kb Manual 36 pages 44.82 Kb Manual 36 pages 4.31 Kb Manual 25 pages 23.47 Kb Manual 36 pages 14.89 Kb Manual 36 pages 10.71 Kb Manual 25 pages 19.68 Kb Manual 25 pages 63.09 Kb

AR09MSPXAWKXEU, AR12MSWXBWKNEU, AR12MSPXASIXEU, AR09MSPXASIXEU, AR07MSWXBWKNEU specifications

The Samsung AR09MSPXBWKNEU and its counterparts, the AR12MSPXBWKXEU, AR12MSPXBWKNEU, and AR09MSPXBWKXEU, are part of Samsung’s innovative range of air conditioning units designed for superior performance and energy efficiency. These models represent a combination of sleek design, advanced technology, and user-friendly features, catering to residential and commercial cooling needs.

One of the standout features of these units is their powerful inverter technology. This technology allows the air conditioner to automatically adjust its power based on the room's cooling needs, ensuring consistent temperature levels while minimizing energy consumption. As a result, users benefit from lower electricity bills and a reduced environmental footprint.

Another significant characteristic is the Triple Protector Plus technology. This feature enhances the durability of the units by providing protection against voltage fluctuations, operating without stabilizers, and preventing corrosion on the unit's surface. This ensures that the air conditioners can withstand varying weather conditions and are built to last longer.

The Wind-Free cooling technology further sets these models apart. It enables a comfortable environment by dispersing cool air through micro-holes, creating a gentle breeze without the uncomfortable direct airflow. This results in a more pleasant indoor climate and can contribute to better overall health and comfort for occupants.

In addition, the AR09MSPXBWKNEU and AR12MSPX series are equipped with a user-friendly Smart Things application that allows users to control their air conditioning units remotely. This capability offers convenience and flexibility, enabling scheduling, temperature adjustments, and even monitoring of energy consumption directly from a smartphone.

Furthermore, these models come with easy-to-clean filters that are washable, promoting better air quality by trapping dust and allergens, which can be particularly beneficial for individuals with allergies or respiratory conditions.

Lastly, the modern and minimalist design of the Samsung air conditioning units ensures that they seamlessly blend into any interior decor, making them not just functional appliances but also aesthetic additions to the space.

In summary, Samsung’s AR09MSPXBWKNEU, AR12MSPXBWKXEU, AR12MSPXBWKNEU, and AR09MSPXBWKXEU air conditioners showcase cutting-edge technology, robust features, and energy efficiency, making them excellent options for consumers looking to enhance their indoor climate conditions.