Samsung AR12MSPXBWKXEU, AR12MSPXASINEU Installation Inspection, Running the Smart Install mode

Page 21

Installation Inspection

Step 4.1 Performing the gas leak tests

1Before inspecting the leakage, use a torque wrench to close the cap for the stop valve. (Comply with a tightening torque for each size of the diameter, and tighten the cap firmly to prevent any leakage.)

Tightening torque for body cap (Refer to the table)

Charging core

Spindle

R-22: Thread of the screw - 7/16-2OUNF

R-410A: Thread of the screw -1/2-2OUNF

Tightening torque for charging port cap (Refer to the table)

Outer diameter

Tightening torque

(mm)

Body cap (N•m)

Charging port cap (N•m)

 

 

 

 

ø 6.35

20 to 25

 

 

 

 

ø 9.52

20 to 25

 

 

 

 

ø 12.70

25 to 30

10 to 12

 

 

 

ø 15.88

30 to 35

 

 

 

 

Over ø 19.05

35 to 40

 

 

 

 

( 1 N•m = 10 kgf•cm )

2Insert inert gas into the pipes connected to indoor and outdoor units.

3Test leakage on the connection parts of the indoor and outdoor units with soap lather or liquid.

Test parts for the indoor unit

Test parts for the indoor unit

Step 4.2 Running the Smart Install mode

If using a multi system, this function is not supported.

1Make sure that the air conditioner is in the standby status.

2Hold down the (Power), (Mode) and

(SET / Temperature type ()) buttons on the remote control simultaneously for 4 seconds.

3Wait until Smart Install mode succeeds or fails. It takes approximately 7 to 13 minutes.

• While Smart Install mode is proceeding:

Type

Display

LED Display

 

 

LED1

 

 

LED2

 

 

LED3

Indoor

 

 

unit

The progress is

The LEDs on the

indicator

indoor unit display

 

displayed as a

blink in sequence,

 

number between

 

then all of them

 

0 and 99 on

 

blink simultaneously.

 

the indoor unit

 

These operations

 

display.

 

repeat.

 

 

When Smart Install mode succeeds: Smart Install mode ends with ringing sound, and the air conditioner is in standby status.

When Smart Install mode fails: An error message is displayed on the indoor unit display, and Smart Install mode ends.

NOTE

Smart Install mode can be operated only with the supplied remote control.

During the Smart install mode procedure, remote control cannot be operated.

English 21

Installation

Image 21
Contents Air conditioner Contents General information Safety Information on InstallationFires, explosions or injuries Install the unit in a place where water can drain smoothlyPreparation Choosing the installation locationMinimum clearances for the outdoor unit CasesAccessories Accessories in the indoor unit packageUnit mm Tools General tools Accessories in the outdoor unit packageTools for test operation Thermometer Resistance meter Electroscope EnglishTaping the pipes, cables, and drain hose Drilling a hole through the wallInstallation plate Indoor Unit InstallationDisassembling the cover panel Remove the cap screws, then the screwsConnecting the Power and communication cables assembly cable Compression dimension should be Optional Extending the power cableInstall the drain hose Installing and connecting the drain hoseOptional Extending the drain hose FireOptional Changing the direction of the drain hose Pass the pipe through the hole in the wall Shortening or extending the refrigerant pipes assembly pipe10 Fixing the installation plate When fixing the indoor unit on a wallWhen fixing the indoor unit on a window frame When fixing the indoor unit on a gypsum board 11 Fixing the indoor unit to the installation plateFix the installation plate without inclining to one side 12 Assembling the cover panelFixing the outdoor unit in place Outdoor Unit InstallationRefrigerant pipes That the fan can operate correctlyLeave the system in the standby mode Evacuating the airCooling capacity and malfunction. Use a vacuum pump Siphon Adding refrigerant①+②, c Running the Smart Install mode Installation InspectionPower cable or communication Error betweenMotor Connector Remove foreign substance. Check Blocking error OpenPerforming final check and trial operation Check the following Strength of the installation sitePumping down for removing the product Let the compressor run for more than 5 minutesSub PCB installationoptional Attach the Sub PCB to the Case Sub PCBAssemble the Case Sub PCB to the indoor unit DB68-06732A-03
Related manuals
Manual 2 pages 25.92 Kb Manual 39 pages 32.94 Kb Manual 25 pages 2.73 Kb Manual 36 pages 62.01 Kb Manual 36 pages 15.94 Kb Manual 36 pages 60.74 Kb Manual 36 pages 44.82 Kb Manual 36 pages 4.31 Kb Manual 25 pages 23.47 Kb Manual 36 pages 14.89 Kb Manual 36 pages 10.71 Kb Manual 25 pages 19.68 Kb Manual 25 pages 63.09 Kb

AR09MSPXAWKXEU, AR12MSWXBWKNEU, AR12MSPXASIXEU, AR09MSPXASIXEU, AR07MSWXBWKNEU specifications

The Samsung AR09MSPXBWKNEU and its counterparts, the AR12MSPXBWKXEU, AR12MSPXBWKNEU, and AR09MSPXBWKXEU, are part of Samsung’s innovative range of air conditioning units designed for superior performance and energy efficiency. These models represent a combination of sleek design, advanced technology, and user-friendly features, catering to residential and commercial cooling needs.

One of the standout features of these units is their powerful inverter technology. This technology allows the air conditioner to automatically adjust its power based on the room's cooling needs, ensuring consistent temperature levels while minimizing energy consumption. As a result, users benefit from lower electricity bills and a reduced environmental footprint.

Another significant characteristic is the Triple Protector Plus technology. This feature enhances the durability of the units by providing protection against voltage fluctuations, operating without stabilizers, and preventing corrosion on the unit's surface. This ensures that the air conditioners can withstand varying weather conditions and are built to last longer.

The Wind-Free cooling technology further sets these models apart. It enables a comfortable environment by dispersing cool air through micro-holes, creating a gentle breeze without the uncomfortable direct airflow. This results in a more pleasant indoor climate and can contribute to better overall health and comfort for occupants.

In addition, the AR09MSPXBWKNEU and AR12MSPX series are equipped with a user-friendly Smart Things application that allows users to control their air conditioning units remotely. This capability offers convenience and flexibility, enabling scheduling, temperature adjustments, and even monitoring of energy consumption directly from a smartphone.

Furthermore, these models come with easy-to-clean filters that are washable, promoting better air quality by trapping dust and allergens, which can be particularly beneficial for individuals with allergies or respiratory conditions.

Lastly, the modern and minimalist design of the Samsung air conditioning units ensures that they seamlessly blend into any interior decor, making them not just functional appliances but also aesthetic additions to the space.

In summary, Samsung’s AR09MSPXBWKNEU, AR12MSPXBWKXEU, AR12MSPXBWKNEU, and AR09MSPXBWKXEU air conditioners showcase cutting-edge technology, robust features, and energy efficiency, making them excellent options for consumers looking to enhance their indoor climate conditions.